DIY 30 Ton Hydraulic Forge Press Part 3
In this final installment, I assemble the press, do some troubleshooting, and put it through its paces. Red Beard Ops - / @redbeardops Tyrell Knifeworks - / @tyrellknifeworks Hydraulic Cylinder - https://northernhydraulics.net/catalo... SAE 12 x 1/2" NPT 90 Degree Fittings (Need to purchase 2) - https://www.surpluscenter.com/Hydraul... Prince Hydraulic Directional Valve - https://www.surpluscenter.com/Hydraul... NOTE - YOU MUST HAVE A PRESSURE GUAGE INSTALLED IN ORDER TO ADJUST PRESSURE* TO ADJUST PRESSURE - Turn Adjustment Screw CLOCKWISE to INCREASE Pressure / Turn COUNTER-CLOCKWISE to DECREASE Pressure Route Port A of Valve to Top Port on Cylinder, and Port B of Valve to Bottom Port on Cylinder in order to have the ram engage when toe on foot pedal is pressed down. The handle will engage the ram when pressed toward ceiling, and will retract the ram when handle is pulled down. Oil Filter - LENZ Spin-On Filters Assembly CP-750-10P: 10 Filter Micron, 100 PSI, 20 GPM, 3/4” NPTF Port, 15 PSI Bypass, No Indicator Ports, 221005 https://a.co/d/ivTX2yh Coupler Set - 1/2" to 5/8" L075 Flexible 3-Piece L-Jaw Coupling Coupler Set & Rubber Spider https://a.co/d/fz2IJT8 Pump - Bestauto Hydraulic Wood Splitter Pump 3000 PSI 2 Stage Log Splitter Pump 13 GPM, Hydraulic Gear Pump 3600 RPM Aluminum Log Splitter Pumps 1/8" Keyed Shaft for Gas Log Splitters/Hydraulic Power Units https://a.co/d/3gUGqKB Reservoir - https://www.northerntool.com/products... Reservoir Strainer - Buyers Products SW2001253 Thru-Wall Sump Strainer (Strainer Thru-Wall 2In X 1 1/4In) https://a.co/d/d5vCRVs 3/4" Return Line Hose - Apache 98398374 3/4" x 36" 2-Wire Hydraulic Hose Male x Male Assembly https://a.co/d/6twucZ2 1" Suction Hose - Apache 98392250 1" x 5' Low Pressure Hydraulic Return Line Hose with Worm Gear Clamps https://a.co/d/2EHXwoB 5hp Motor - https://www.ebay.com/itm/5-HP-SPL-345... Thanks again for hanging out with me during this build. I really appreciate everyone who has taken the time to show some interest.

DIY 30 Ton Hydraulic Forge Press Part 1

Hydraulic press build - FORGING PRESS

Presse hydraulique de forge 30T - Fabrication

DIY 30 Ton Hydraulic Forge Press Part 2

Building my 50 Ton Forge Press from start to finish!!!(43ish)

40 Years Old Hydraulic System Converted into Forging Press

Huge ribbon burner forge build part 1

The PROBLEM with Capitalism - Smarter Every Day 316

Making super light, resolvable 25 TON forging press: full guide

Knife Making - Hydraulic Press for knife Maker

Making a jib crane for the shop. Part 1

Building a 16 Ton Hydraulic FORGING PRESS

Episode 3: Complete Front Axle Restoration | Renault 4

HOW TO BUILD A HYDRAULIC PRESS - FORGING PRESS

£300 *30ton* hydraulic press for under! - Vevor hydraulic power pack air pump cylinder reveiw

Making Tooling To Forge YOUR Hammers! Blacksmithing

Building a big forge press for blacksmithing

Building a 24 Ton Log-Splitter Forging Press!

Hydraulic Forging Press Build

