[OLD VERSION - SEE V3] Learn STM32 Microcontroller Programming - Full Course

Link to the new Version 3:    • Learn STM32 Microcontroller Programming - ...   Get the kits to complete these projects here: https://buildyourcnc.com/collections/... Get the companion book here: https://amzn.to/49Bv8QX If you wish to support me and the efforts in making more content: https://buymeacoffee.com/patrickhoodd... Join this channel to get access to perks:    / @patrickhooddaniel   00:00 Introduction 00:03:35 Introduction to Bare Chip Microcontroller Development 00:06:39 The Prototyping Setup 00:10:22 IDE and Monitoring Software Setup 00:16:03 Getting Familiar with the STM32CubeIDE 00:18:51 Creating a Project in the IDE 00:22:27 Transferring the program to the microcontroller 00:25:20 Monitoring Runtime Data using STMStudio or STMCubeMonitor 00:30:14 Troubleshooting 1: Chip erase using the boot pin 00:31:46 Troubleshooting 2: Chip erase using the reset pic 00:33:02 Troubleshooting 3: Power on AVCC not present 00:37:14 "4 Most Important Code Instructions - Changing and testing bits" 00:43:15 "Project 1: Turning on an LED The ""Hello World"" of MCU Projects" 01:02:17 Project 2: Receiving Input from a Button 01:18:10 Project 3: Latching an Input 01:32:09 Project 4: Interfacing an LCD Display 02:50:34 Using pointers to construct a string of characters 02:55:51 Project 5: Sending integers to the LCD 03:02:36 Project 6: Send floating point numbers to the LCD 03:07:49 Project 7: Set the location on the LCD 03:17:40 ADC (analog to digital conversion) introduction 03:27:49 "Project 8: ADC Conversion (internal temperature sensor)" 03:51:39 "Project 9: Converting the ADC value to a meaningful number, Temperature" 04:00:08 Project 10: Potentiometer as the ADC input 04:07:28 "Project 11: Timers and Counters Prescaler (Skip Oscillations)" 04:17:34 "Project 12: Timers and Counters: ARR (Auto reload register) Top Count Limit Count Direction Center Aligned Mode (Zig Zag Counting)" 04:22:46 "Introduction to PWM (Pulse width modulation)" 04:30:23 "Project 13: PWM (Pulse width modulation)" 04:44:51 Project 14: Creating an ADC Header File 04:54:07 "Project 15: Control PWM Output with the ADC Attempted to read the PWM with ADC, but an RC Circuit (to smooth the square wave) is required, so that attempt failed." 05:00:15 "Project 16: Control the Dimming of an LED using PWM Controlled by a Potentiometer Through the ADC" 05:01:49 "Project 17: Control a Hobby Servo with the PWM Output" 05:19:43 "Project 18: Control a Hobby Servo with a potentiometer connected to the ADC which controls the PWM for the Servo" 05:25:59 Introduction to Interrupts 05:32:30 Project 19: Using interrupts for ADC Conversion 05:46:23 "Project 20: Using interrupts for ADC Conversion 2 Channels" 05:56:24 Project 21: Fixing an Artifact on the LCD 06:01:42 Project 22: Push Button Interrupt 06:14:08 Project 23: External Interrupts on two pins 06:18:42 "Project 24: Switch output to the STMStudio rather than the LCD" 06:26:04 "Introduction to the I2C or IIC communication protocol" 06:38:13 "Project 25: Communicating with the ADXL 345 Accelerometer using the I2C communication protocol Writing a single byte" 07:04:19 "Project 26: Communicating with the ADXL 345 Accelerometer using the I2C communication protocol Reading a single byte" 07:13:38 "Introduction to USART and other communication protocols" 07:23:41 Project 27: Change the close speed to 48mhz 08:01:01 Project 28: Initialize the USART