ЗАМЕНА ПОДШИПНИКА ЗАДНЕЙ СТУПИЦЫ НА РЕНО АРКАНА, ДАСТЕР, КАПТУР, НИССАН ТЕРРАНО 4X4. #ВИДЕОЛЕКЦИЯ

#ZENICOM #EVERYDAYSERVICE #CARSERVICE #CARREPAIR PARTS FROM ALL OVER THE WORLD WITHOUT FAKE PRODUCTS http://bit.ly/2HRzuFh How to remove and install the brake pads for proper rear wheel bearing replacement, watch here    • КАК ЛЕЧИТЬ СКРИП ТОРМОЗОВ? ЗАМЕНА ЗАДНИХ К...   Do you hear a humming or howling noise from the rear of your Renault Duster, Kaptur, or Nissan Terrano while driving? Learn how to change the rear wheel bearing yourself (ON 4WD DUSTER, KAPTURA, AND TERRANO). 90% of the time, it's the problem! Bearing kit numbers: Duster 4x4, Kaptur 4x4, Terrano 4x4 RENAULT 402109533R, SNR R155114. Duster 2x4, Kaptur 2x4 RENAULT 432102069R, SNR FC41722S01 Buy bearings from us using this link https://zenicom.ru/product/%d0%b7%d0%... Video Content: 0:00 INTRO 0:28 A little bit (just a little bit) of advertising 1:52 Toning it down Handbrake cables from the passenger compartment and the hub nut 2:24 Raise the car and remove the desired wheel 2:27 What to do if the wheel is not unlocked? 3:08 Soaking the drum, knuckle, and shock absorber mounting bolts 3:47 Cleaning and soaking the brake line 4:18 Knocking out the drum and unscrewing the screws 5:53 Removing the drum 6:44 Disassembling the pads    • КАК ЛЕЧИТЬ СКРИП ТОРМОЗОВ? ЗАМЕНА ЗАДНИХ К...   7:10 Unscrewing the stripped hub nut 7:19 Soaking the hub-drive connection 7:25 Knocking the drive out of the hub 7:49 Removing the ABS sensor 9:30 Unscrewing the rear control arm bolts to the knuckle 10:56 Unscrewing the shock absorber mounting bolts to the knuckle 11:37 What to do if the bolt is stuck 12:12 Unscrewing the brake line nipple 13:13 Releasing the drive from the hub and Remove the knuckle 13:38 Block the brake cylinder nipple 13:45 Clean the working part of the hub 13:54 Break off the retaining ring 14:10 Knock the hub out of the knuckle 14:51 Remove the retaining ring 16:09 Press out the bearing from the knuckle 16:28 Clean and clean the knuckle for the new bearing 17:13 Proceed to install the new bearing 17:52 Press the new bearing into the knuckle 18:19 Install the new retaining ring 18:55 Remove the old bearing race from the hub 20:43 Clean all mating surfaces of the hub 20:55 Install the hub into the knuckle 22:21 Important preparations before knuckle assembly 23:21 Install the knuckle 23:40 Tighten the brake nipple Tubes 24:08 Inserting all the bolts 24:17 Assembly nuances 25:01 Installing the ABS sensor 25:26 Pulling the handbrake cable through 25:30 Assembling the brake pads    • КАК ЛЕЧИТЬ СКРИП ТОРМОЗОВ? ЗАМЕНА ЗАДНИХ К...   and bleeding the brakes ------------------------------------------------------------------------------------------------    / @zenicom   Sponsor the channel for perks Did you save money on repairs? Find out what part is on your car? Just liked the video? Want to see more? Help the channel with money: http://www.donationalerts.ru/r/petrth... --------------------------------------------------------------------------------------------- -Do you have a question? -Is this possible? -Yes, write to: [email protected]