Budowa drona FPV od A do Z (2025) | #3: Lutowanie, podłączanie i testy podzespołów - VTX, RX, Buzzer

Hi! 👋 Welcome to the third episode of the series *"Building an FPV Drone from A to Z (2025)"* 🎥🚁 . We're about halfway through the whole process! In this episode: 🔧 we'll prepare the pads for soldering, 🧴 we'll tin them, 🔌 we'll solder the components, ⚡ and finally, we'll check everything with a multimeter and a smoke stopper to make sure there are no short circuits. To solder and connect, we have: 🔸 Buzzer (iFlight YR50B_s Finder) 🔸 ELRS Receiver (Radiomaster XR1) 🔸 Walksnail VTX (Nano V3) 🎓 This series is a great resource: – for those just starting out in FPV – for those looking to build their new quad in 2025 --- 📦 Component List: 🔹 Frame: TBS Source Podracer 4 🔹 FC + ESC: Speedybee AIO F405 40A 🔹 Motors: T-Motor Pacer 1804 2400KV 🔹 Propellers: Gemfan Hurricane 4023-3 🔹 VTX: Walksnail Avatar Nano V3 🔹 Receiver: ELRS Radiomaster XR1 + 2.4GHz Antenna 🔹 Buzzer: iFlight YR50B_s Finder 🔹 Kanopki: Custom, designed by PoD 😁 🚨 The kanopki model is available for everyone to download on my Patreon 👌 🔹Link:   / model-3d-kanopki-135726237   💰 Estimated construction cost: approx. 1500–1700 PLN gross --- 🛠️ Tools I use 🔹 Set of Allen and Torx bits with a Wolfcraft screwdriver 🔹 Graphite screwdriver 🔹 Tweezers 🔹 Pliers and pliers 🔹 Precision knife with interchangeable blades blades 🔹HGLRC RC2 soldering iron + TS-B2, TS-D24, TS-BC2, TS-I tips 🔹Tin Cynel SN60PB40 SW26/2.5% - 0.5mm, 1mm, and 2mm 🔹Copper braid 🔹Flux Kester 186 🔹Six-pointed "third hand" 🔹Tip cleaner 🔹Graphite lighter or heat gun 🔹Insulating tape and double-sided sponge tape 🔹Black cable ties 🔹Heat shrink tube set 🔹Multimeter and smoke stopper 🔹Caliper 🔹Set of allen screws and nuts M2, M2.5, M3 🔹USB cable DATE --- 📺 Chapters 00:00 – Introduction 00:43 – Whitening the Pads 06:51 – Soldering the Buzzer 09:51 – Soldering the RX 16:32 – Connecting the VTX 21:34 – Summary and Conclusion --- 📢 If you liked this episode, leave a thumbs up 👍 🔔 Subscribe to the channel so you don't miss the next parts of the series! 📬 And if you have any questions – feel free to ask in the comments, I'll help! --- 💖 Support the channel's development: 🔹 YouTube – Join the community: 👉    / @prosto_o_dronach   🔹 Patreon – Support and additional materials: 👉   / prostoodronach   Thanks for watching and happy flying! 🛸 --- #FPV #drones #dronebuilding #dronebuild #ProstoODronach #fpvbuild #walksnail #dronFPV #drone #speedybee #t-motor #ExpressLRS