Concrete Dining Table | Complete DIY Build

DIY Concrete Dining Table how to video tutorial. This is an excellent DIY concrete project for beginners and the more experienced alike! This clean, modern, minimalist design approach will look great in your dining room. This project doesn’t take that long to make and is attainable by anyone if you follow this step-by-step tutorial. Best of luck on yours! This particular 1 1/2″ concrete top weighs about 370 pounds total. For more info, project photos, and downloadable plans check out: http://www.diypete.com/ConcreteDining... Download Plans: http://gumroad.com/l/ConcreteDiningTable *Note that these are affiliate links, meaning that when you buy something that is recommended below, it helps support the Channel. Thanks in advance! *Tools Needed Miter Saw​ - https://amzn.to/40pmuPc Table Saw - https://amzn.to/2Fc5pP6 OR Circular Saw - http://amzn.to/1OxNa7k Drill and Impact Driver- https://amzn.to/42qaCza Orbital Sander - http://amzn.to/1VUVNYy Concrete Trowel - http://amzn.to/1Lp87Kp Respirator mask - http://amzn.to/1Lp80ym Looking for more recommendations on concrete tools? Check out my Amazon Store: https://www.amazon.com/shop/petesveen... *Supplies Needed Quikrete Countertop Mix or Quikrete 5000 (less expensive option) Cheng Concrete Sealer -http://amzn.to/1Qx83QO 100% Silicone - http://amzn.to/1Qx847e 4 – L Brackets/Joists - http://amzn.to/1Lp83KJ Gorilla Wood Glue - http://amzn.to/1Lp7Zuk Minwax Polyurethane - http://amzn.to/1Qx86fd Approximate Total Cost: $200 The Concrete Dining Table can be made for under $200 dollars in materials cost (at time of this build). This is the cost for the concrete, wood, wood finish, concrete sealer, and other basic supplies. This estimate considers you’re using Quikrete 5000 as a more affordable option. Assemble Melamine Form You should set that large, bottom piece of the melamine form on a flat, level work surface. With melamine forms, you’ll want to be sure to keep it very clean and make sure there are no imperfections or chipping in any of the boards. Whatever faces the inside of the form will translate onto the concrete top after it’s poured. We’ll assemble the sides with 1 ½ wood screws. Be sure to pre drill all holes before adding the screws and make sure everything is square, level, and flush when you’re screwing it together. Don’t add wood glue to the sides of the melamine form, because we’ll need to easily deconstruct it later. Pour Concrete into Form After mixing up the tubs concrete and getting it to a consistency that is peanut-butter-like, then we’ll add it to the form. Wear gloves for this process, spread the concrete evenly in the form and fill it about ⅔ full. Once you’ve reached ⅔ and have spread all of the concrete out evenly, we’ll add the piece of rebar reinforcement to the form. Place it into place and keep adding more concrete to fill it to the top of the form. Screed, Trowel, and Let Cure Once you’ve filled the form with your concrete mixture, we’ll want to level and smooth it all out. Using a scrap 2×4 piece of wood will work fine for the level and screeding of the concrete. Scrape the board from one side of the form to the other in a back-and-forth motion, scraping excess concrete out of the form and working it into low spots. Then we can vibrate the concrete either with a mallet, reciprocating saw (without the blade in), or orbital sander. Spend some time vibrating the concrete. Then trowel it all with a clean trowel and cover the whole concrete top with a plastic cover to help it cure evenly. Let the concrete cure and dry for the manufacturers recommended time. Once it has hardened slightly, you can come through and do a hard trowel of the bottom. Refer to the video for more information about this technique. Build the Base Legs Once you’ve poured your concrete and it is taking the necessary time it needs to cure, then we’ll move onto building the wood base. The wood base is a modern, simple design and should not take that long to build. Refer to the cut list in the plans for help in deciphering which base pieces go where. Your base basically consists of two 4×4 constructed boxes on each end and three 4×4 support stretchers running between the top of the boxes. When putting the joints together with the torx screws, be sure to pre drill to avoid any splitting of the wood. Also, generously add wood glue to the joint to ensure security and strength...more at http://www.diypete.com/ConcreteDining... ---- Looking for more DIY videos? Be sure to check out our channel and subscribe for updates! Looking for woodworking, concrete working, and other DIY projects plans to follow? You can download plans at http://gumroad.com/DIYPETE and https://www.diypete.com/diy-project-p... Facebook:   / diyprojectswithpete   Instagram:   / diypete   DIYPETE.com 1627 W Main Street Suite 182 Bozeman, Montana 59715 #concreteprojects #diytable #diningtable