Wie Peugeot 206 Hinterachse wechseln 🚗

BUY the necessary parts for the process: 👉 http://bit.ly/AutoteilePreiswert 👈 📱 DOWNLOAD THE APP: 🍎 http://bit.ly/MCD12AppStore, 🤖 : http://bit.ly/MCD12PlayStore 📱 ⬇︎⬇︎ 🔥 🔧🔧🔧 🔥⬇︎⬇︎ 🛠📏⚙ HERE YOU WILL FIND THE PARTS AND TOOLS USED AND RECOMMENDED BY USETOOL ⚙📏🛠 Required parts: Rear axle Penetrating oil: https://maclede12.co/Kriechoelde Electrician's clamps Rear bridge crossbar (SW version) Threadlockers 💪 TIGHTENING TORQUES FOR REPLACING THE REAR AXLE PEUGEOT 206 Rear axle shafts: impossible to find. If you have any, let us know in the comments. Rear axle mounting bolt: 30 Nm Rear axle/frame mounting bolt: 110 Nm Stem Phillips head bolt: 105 Nm Fork crown bolt: 105 Nm Upper shock absorber mounting bolt: 70 Nm Lower shock absorber mounting bolt: 150 Nm Table top retaining bolt: 35 Nm Hub nut: 200 Nm Discover the numerous services that will be useful for maintaining your bike: service booklets, maintenance planning, and mechanic-oriented tutorials! Replacing the rear axle on a Peugeot 206. Discover the world of UseTool at http://bit.ly/2mtjtft Tools required: -💣🤖🏆The complete toolbox recommended by UseTool for repairing your 206: https://maclede12.co/werkzeugkofferCL... 🏆🤖💣 Hammer Precision flat chisel Articulated handle 32 mm socket ​​Socket wrench Extension bar Torx 45 socket ​​10 mm socket ​​Flat screwdriver 13 mm socket ​​Wire or hook 18 mm open-end wrench 18 mm socket ​​21 mm open-end wrench 21 mm socket ​​Pin punch Metal brush Side cutters 16 mm socket ​​19 mm open-end wrench Pipe wrench Sandpaper Torque wrench: https://maclede12.co/drehmomentschlue..., https://maclede12.co/drehmomentschlue..., https://maclede12.co/drehmomentschlue... Tape measure 🔝💪 UseTool recommends the car jack: https://maclede12.co/wagenheberCLASOH... and the jack stands: https://maclede12.co/unterstellbockCL... to safely lift your 206 💪🔝 Hydraulic jack Jack stand 🚗📢💡 RESOURCES 💡📢🚗 UseTool warnings To avoid damaging the silent blocks, the retaining screws must be loosened. The rear axle must be tightened with the vehicle on the ground. Before final tightening, use a tape measure to ensure that the clevis is exactly centered on the axle. Information from UseTool To lower the exhaust silencer, the left rear axle cross member must be relocated by unscrewing the strut. 📽❤️🚨 USEFUL VIDEOS 🚨❤️📽 [USETOOL TIPS & TRICKS] How to safely lift your car:    • So hebst du dein Fahrzeug (RICHTIG) sicher...   [USETOOL TIPS & TRICKS] How to use a torque wrench (PROPERLY) 🔧 :    • So verwendest du einen Drehmomentschlüssel...   Space Race by tubebackr |   / tubebackr   Music promoted by https://www.free-stock-music.com General information about the offer: https://www.mister-auto.de/betrieb/16... Disclaimer: This video was created for informational purposes and does not guarantee the results. To ensure the best possible result, we recommend that you contact qualified technicians for installation. This video provides tips and recommendations that may be useful for repairs or part replacements. MCD12 and its partners cannot be held responsible for any physical or material damage resulting from the misuse or misinterpretation of this video content. This video was produced for informational purposes and in no way guarantees any expected results. The user bears sole responsibility for any misuse of repair equipment, tools, and spare parts, especially if they are exposed to physical damage. MCD12 and its partners recommend extreme caution and strict adherence to safety regulations when performing repair or replacement work. Please note that the use of inferior parts compromises the driver's safety. 0:00 Introduction 0:23 Lifting the vehicle 1:06 Removing the axle 6:13 Recovering components 6:34 SW-specific components 9:14 Reinstalling SW-specific components 10:40 Reinstalling the rear axle