Controforma girevole per violino - Rotating counterform (cradle) for violin

Questa è la controforma che utilizzo per la lavorazione delle tavole di violino, dalla sgrossatura delle bombature fino allo scavo dell'interno per la finitura degli spessori, nonché per alcuni lavori successivi alla chiusura della cassa. This is the counterform (cradle) I use for working on violin plates, from roughing out the arching to hollowing out the inside for finishing the thicknesses, as well as for some work after the soundbox has been closed. ⬇️⬇️ (English translation below the Italian text) ⬇️⬇️ 0:00 - Controforma girevole per violino 0:24 - Realizzare la controforma utilizzando un pezzo di mogano o altro legno duro, 40 cm di lunghezza x 25 mm di larghezza x 3 cm di spessore, scavando la parte centrale per accogliere la bombatura e modellando il contorno in modo appropriato 1:21 - Utilizzare rovere o altro legno molto duro e rigido per realizzare il pezzo di supporto della controforma 1:33 - Incollare del sughero sulle superfici a contatto con la controforma e con la morsa del banco da lavoro, per facilitare il bloccaggio 2:02 - Inserire 3 viti per rinforzare la resistenza del giunto tra le parti incollate 3:02 - Utilizzare compensato di faggio e plastica rigida (Formica) per realizzare 4 fermi regolabili, proteggendo la superficie di contatto con il bordo delle tavole con del sughero 3:15 - Incollare della carta vetrata a grana grossa sulla superficie inferiore a contatto con la controforma, per favorire il bloccaggio e impedire lo scivolamento 3:39 - Sughero 3:50 - Utilizzare un bullone M12 in ottone per il perno centrale 4:09 - Levigare e arrotondare bene i bordi della parte superiore della testa esagonale 4:19 - Inserirla nella culla in modo che non sporga dalla superficie di appoggio, per evitare il contatto diretto con il legno delle tavole 5:07 - Inserire quattro pezzi di sughero sagomati per accogliere la sporgenza delle punte, per non danneggiarle durante la lavorazione dell'interno delle tavole 5:31 - Inserire due fermi girevoli durante la lavorazione dell'interno delle piastre, per evitare che scivolino fuori accidentalmente 6:00 - Per questi perni utilizzare legno tenero (compensato di pioppo), arrotondando con cura i bordi interni per evitare di danneggiare la superficie di incollaggio delle tavole ⬇️⬇️ (English translation of the Italian text with timestamps) ⬇️⬇️ 0:00 - Rotating cradle for violin 0:24 - Make the cradle using a piece of mahogany or other hardwood, 40cm length x 25mm width x 3cm thickness, digging the central part to accommodate the arching and shaping the outline appropriately 1:21 - Use oak or other very hard and stiff wood to make the support piece of the cradle 1:33 - Glue some cork on the surfaces in contact with the cardle and with the vice of the workbench to ease locking 2:02 - Put 3 screws to reinforce the strength of the joint between the glued parts 3:02 - Use beech plywood and hard plastic (Formica) to make 4 adjustable stops, protecting the surface of contact with the edge of the plates with cork 3:15 - Glue coarse sandpaper on the underside surface in contact with the cradle, to favor the blocking and prevent slipping 3:39 - Cork 3:50 - Use an M12 bolt made of brass for the central pivot 4:09 - Smooth and round off well the edges of the upper part of the hexagonal head 4:19 - Fit it in the cradle so that it is not protruding from the supporting surface, to avoid direct contact with the wood of the plates 5:07 - Insert four pieces of cork shaped to accommodate the protrusion of the corners, not to damage them when working the inside of the plates 5:31 - Insert two swiveling stops when working the inside of the plates, to keep them from slipping out accidentally 6:00 - Use soft wood (poplar plywood), rounding carefully inside edges to avoid damaging the gluing surface of plates Index of all my videos on violin making: English: https://davidesora.altervista.org/vid... Italiano: https://davidesora.altervista.org/video/ Davide Sora® is a registered trademark Davide Sora® è un marchio registrato #costruzioneviolino #violinmaking