BMW R60/5 Rear Shock Disassembly | Motorcycle Rear Shock

Since I am going through the whole BMW R60/5, I need to clean up the rear shocks and make sure everything is up to working standards for a safe ride. Once that's all in order I can give them a fresh coat of paint. In this video, I will share with you how to take apart rear motorcycle shocks with very few tools. These happen to be from my BMW project, but most classic rear shocks have the same setup! The damper must be removed from the top retainer. With a little bit of heat, you can easily remove these two parts without damaging anything during the process. After everything was apart I focused on the silent blocks (rubber bushings) within the shaft eyelet and top retainer. For this, I used two sockets on either side and this will act just like a press within the vice. If this video was helpful in any way, I'd appreciate it if you hit that like button and if you want to be one of the first to see the assembly video, be sure to subscribe! 🔽Check out my Merch Store🔽 https://workshop-rebuild.creator-spri... ________________________________________________________________________ Watch My Previous Rebuilds: 𝐁𝐌𝐖 𝐑𝟔𝟎/𝟓 𝐌𝐨𝐭𝐨𝐫𝐜𝐲𝐜𝐥𝐞 𝐏𝐫𝐨𝐣𝐞𝐜𝐭: https://bit.ly/3uJVXOn 𝐉𝐨𝐡𝐧 𝐃𝐞𝐞𝐫𝐞 4𝟎𝟎: https://bit.ly/3unVNfg 𝐉𝐨𝐡𝐧 𝐃𝐞𝐞𝐫𝐞 𝟑𝟎𝟎:https://bit.ly/3BbuWDz 𝐉𝐨𝐡𝐧 𝐃𝐞𝐞𝐫𝐞 𝟑𝟏𝟕:https://bit.ly/3wHy2x5 𝗕𝗼𝗹𝗲𝗻𝘀 𝗛𝗧𝟮𝟬 𝗣𝗿𝗼𝗷𝗲𝗰𝘁: http://bit.ly/2NOLvlp 𝗔𝗹𝗹𝗶𝘀 𝗖𝗵𝗮𝗹𝗺𝗲𝗿𝘀 𝐂/𝐁 𝗧𝗿𝗮𝗰𝘁𝗼𝗿: http://bit.ly/3bvXLzd 𝗧𝗵𝗼𝗺𝗮𝘀 𝗛𝗟𝟭𝟳𝟯 𝗦𝗸𝗶𝗱 𝗦𝘁𝗲𝗲𝗿: http://bit.ly/3pDTBKM 𝗝𝗼𝗵𝗻 𝗗𝗲𝗲𝗿𝗲 𝟔𝟖/𝟕𝟎 𝗣𝗿𝗼𝗷𝗲𝗰𝘁: http://bit.ly/3bKGra3 𝐁𝐨𝐛𝐜𝐚𝐭 𝟕𝟓𝟑 𝐏𝐫𝐨𝐣𝐞𝐜𝐭: http://bit.ly/37EDeaD Instagram:   / workshoprebuild   Tiktok: https://www.tiktok.com/@workshoprebui... E-Mail: [email protected] 🎵Music: https://share.epidemicsound.com/v6woxm