Installing the Headlight, Fog, and Turn Signal LED Light Resistors | 2007-2011 Toyota Camry

Hi there! Thanks for watching. This video is part 2 of the light series, which covers the placement of the LED light resistors. The Turn Signal and High Beam Canbus LED lights were screwed onto the metal frame. The low beam and fog LED light resistors did not find a home due to the short length of the cable. The Tools needed for this job are zip ties, a drill, a 1/8" drill bit, 1/8" x 1/2" screws and nuts, and a screwdriver. Please comment below if you have any suggestions for the low beam and fog LED light resistors. 🔴Tools Required for this Job: 🔶Drill: 🔹USA: https://amzn.to/3W84iFC 🔺CAN: https://amzn.to/3H84ctt 🔶Drill Bits: 🔹USA: https://amzn.to/3QJpil9 🔺CAN: https://amzn.to/3k9BiQq 🔶Screw Driver: 🔹USA: https://amzn.to/3CSgxiN 🔺CAN: https://amzn.to/3kdQGvb 🔶1/8" x 1/2" Screws and Nuts (go to Home Depot): 🔹USA: https://amzn.to/3GB7tzW 🔺CAN: https://amzn.to/3QIPEn1 🔶Ziptie: 🔹USA: https://amzn.to/3CRRdJH 🔺CAN: https://amzn.to/3kdQWu9 🔴Common Tools: 🔶Socket Wrench Set: 🔹USA: https://amzn.to/3d2Yhta 🔺CAN: https://amzn.to/3SkuP1A 🔶Wrench Set: 🔹USA: https://amzn.to/3BDJD5T 🔺CAN: https://amzn.to/3PQ43g0 🔶Torque Bar 🔹USA: https://amzn.to/3oKBmoK 🔺CAN: https://amzn.to/3P5MEPv 🔶Breaker Bar 🔹USA: https://amzn.to/3blmcU7 🔺CAN: https://amzn.to/3vyAurn 🔶Rust Penetration 🔹USA: https://amzn.to/3OSu4tZ 🔺CAN: https://amzn.to/3QaAhlV 🔶Gloves 🔹USA: https://amzn.to/3OOXuZJ 🔺CAN: https://amzn.to/3cREg8B 🔶Safety Glasses 🔹USA: https://amzn.to/3zngrgw 🔺CAN: https://amzn.to/3Sbn662 🔶Pneumatic Air Impact Wrench (Optional) 🔹USA: https://amzn.to/3zOxWYF 🔺CAN: https://amzn.to/3oLBuo9 🔶Air Compressor (optional) 🔹USA: https://amzn.to/3oM0go5 🔺CAN: https://amzn.to/3SiQd7x 🔶Exacto Knife: 🔹USA: https://amzn.to/3QFpOR4 🔺CAN: https://amzn.to/3iGDWwM 🔶Pliers: 🔹USA: https://amzn.to/3H6IRjP 🔺CAN: https://amzn.to/3CO10QU 🔶Allen Wrench: 🔹USA: https://amzn.to/3H9FvNm 🔺CAN: https://amzn.to/3Wtk7qN Chapters: 00:00:00 - Intro 00:02:00 - Passenger Side Turn Signal Resistor Installation 00:05:00 - Driver Side Turn Signal Resistor Installation 00:07:07 - Taking a Look at the Canbus Resistor 00:07:48 - Passenger Side Canbus Resistor Installation 00:10:42 - Battery Removal 00:11:12 - Driver Side Canbus Resistor Installation 00:13:05 - Low Beam and Fog Light LED's Reflection 00:17:00 - Final Thoughts and Outro The car that is being worked on is a 2007 Toyota Camry SE 2.4L 4-cylinder engine. This generation of Toyota Camry is called the XV40, which runs from 2007 to 2009. If you want to see something, please comment, and I will do my best to make the content. Disclaimer: With all due respect, the people in the video and channel are not reliable for property damage, personal wellbeing, and trouble with the law from the video/channel contents. Use information at your own risk. When modifying, it is recommended to do lots of research, practice safety, have/wear/use PPE, and look into local/provincial/state/federal traffic laws. Any injury, damage, loss, or trouble with the law from the content of this video/channel is the sole responsibility of the user and not the channel or people in the video. Seek professional help if unsure about anything. Links may contain affiliation. Local/provincial/state/federal traffic laws. Any injury, damage, loss, or trouble with the law from the content of this video/channel is the sole responsibility of the user and not the channel or people in the video. Seek professional help if unsure about anything. Links may contain affiliation.