ВСЁ О ПАЙКЕ. Типичные ошибки новичков. Полезные советы и лайфхаки.

SUPPORT THE CHANNEL (Yumoney): https://musicboy.ru/majortomworkshop SBER CARD: 5336 6900 6775 7700 https://boosty.to/majortom https://t.me/majortomworkshop Advertising. ALIBABA.COM (RU) LLC, INN 7703380158: ORDER EQUIPMENT AND COMPONENTS: DPS-5020 POWER SUPPLY https://rz6.ru/0?erid=2SDnjdoD2Rn SOLDERING IRON from the video https://rz6.ru/1?erid=2SDnjcKTrY8 Soldering iron with desoldering suction https://rz6.ru/2?erid=2SDnje4HgfS Soldering station with hot air gun 702 https://rz6.ru/3?erid=2SDnjdEZctx SOLDERING KIT https://rz6.ru/4?erid=2SDnjc4m2kp Copper tips https://rz6.ru/5?erid=2SDnjd1caBa Solder with flux https://rz6.ru/6?erid=2SDnjc1gg7r MULTIMETER https://rz6.ru/7?erid=2SDnjcz2Cpx OSCILLOSCOPE https://rz6.ru/9?erid=2SDnjdj1qzx USB MICROSCOPE https://rz6.ru/10?erid=2SDnjdbL7jE Set of mont. Wires https://rz6.ru/11?erid=2SDnjcFAxcp Alligator Clips https://rz6.ru/12?erid=2SDnjcbvnZe Stripping Pliers https://rz6.ru/13?erid=2SDnjcnJhY4 Wire Cutters https://rz6.ru/14?erid=2SDnjcwCdE8 Crimping Tool https://rz6.ru/15?erid=2SDnjecdxUx Breadboards https://rz6.ru/22?erid=2SDnjeLL6PA LEDs (5 colors) https://rz6.ru/23?erid=2SDnjcBqpnt SMD Boards https://rz6.ru/24?erid=2SDnjdvcHse Set Transistors https://rz6.ru/25?erid=2SDnjdyzTGC Resistor Set https://rz6.ru/26?erid=2SDnje8tNxG Zener Diode Set https://rz6.ru/27?erid=2SDnjcoMVdA Ceramic Capacitor Set https://rz6.ru/28?erid=2SDnjdhJkwJ Electrolytic Capacitor Set https://rz6.ru/29?erid=2SDnjd5dgEt Diode Set https://rz6.ru/30?erid=2SDnjesWXP6 SMD Resistors 170 Values ​​https://rz6.ru/31?erid=2SDnjdvsQmn SMD Capacitors 90 Values https://rz6.ru/32?erid=2SDnjdhJkwJ #majortomworkshop #majortommusic 0:00 Today we'll talk about soldering! Introduction. 0:30 Why does the soldering iron tip turn black? Why does the solder form balls and not stick to the conductors? 1:20 How to reduce the soldering iron temperature? 1:40 Soldering iron tip gauge. How to choose a soldering iron tip? 2:14 What solder diameter do I need? 2:44 Which tip should I choose? 3:00 All about copper tips. What are the advantages of a copper tip? 3:45 How to avoid overheating wire insulation? 4:10 MGTF wire. What are its advantages? How to strip MGTF wire? 4:24 Different types of wire. Which wire is best for soldering? 5:00 Is it possible to solder without flux? 5:25 Rosin and flux-containing solders. How can you tell if your solder contains flux? 5:35 How to tin wires? 6:07 Liquid rosin 7:00 Desoldering with braid 7:22 Desoldering pump, pressure syringe 7:32 Cleaning boards after soldering 7:55 How much solder should you use when soldering? 8:20 How to properly tin components when soldering? 8:45 Securing components on the board during soldering 9:11 Oxidation of conductors during soldering 9:29 Oxidation on a printed circuit board 9:40 How to properly strip wires? 10:00 Using tweezers 10:20 Proper stripping of stranded wire and cable 11:20 Side cutters: how to choose them? 11:39 Check your work after soldering! 12:10 Types of flux. Neutral and active flux. 12:42 How to properly clean a board after soldering? 12:50 Removing smoke during soldering 13:10 Insulating wires during soldering. Using heat shrink. 13:35 Which electrical tape is best for insulating wires? 14:00 Insulating temporary connections 14:15 Element dimensions and conductor dimensions 14:41 How to repair a damaged track on a printed circuit board? 14:50 How to properly solder connectors? 15:12 How to properly solder DIP chips? 15:52 How to solder ribbon cables? How to avoid damaging the printed circuit board when soldering? 16:33 The more massive the element, the longer the heating time. 16:48 Do not solder over the printed circuit board. 17:15 Do not solder over an unprotected body. 17:33 Danger of flicking off solder. 17:58 Do not use a soldering iron to remove insulation. 18:27 Always use a soldering iron stand; do not place the soldering iron on the table. 18:50 Keep your work surface tidy! 19:11 Do not clean the coated tip with sandpaper! Yellow sponge for cleaning the tip. 19:42 Do not tap the soldering iron on the stand! 19:55 Do not cool the soldering iron with water! 8:00 PM Don't hold components with your hands. Use alligator clips or tweezers. 8:24 PM Don't test the soldering iron's heat by holding it to your face! 8:38 PM Does your soldering iron short out? 9:02 PM Let's come up with a translation for the word "lifehack"! Poll. 9:56 PM How to secure a cable inside a case or connector? 10:06 PM How to desolder a board with lead-free solder? 10:28 PM How to easily apply flux to a board and components? 22:50 Wiggle the leads when using a solder sucker 23:06 Alternate tilt method when desoldering components 23:31 Desoldering microcircuits with a sharpened needle 23:33 Combining soldering with heat shrink 23:43 Cutting out a microcircuit entirely with the PCB 23:55 How to properly extract a microcircuit? 24:14 Cleaning contact pads after soldering 24:25 How to restore a coaxial cable? 24:52 How to remember to turn off the sold...