Screw Thread Terminology | Flank, Pitch, Root, Crest | Thread terms and Nomenclature | Metrology

Subject - Metrology and Quality Control Chapter - Basic terms used in Screw Thread Terminology Timestamps 0:00 - Screw Thread Terminology 0:05 - Thread of Screw 0:18 - Root 0:27 - Crest 0:35 - Flank 0:44 - Angle of Thread 0:51 - Depth of Thread 1:00 - Major Diameter 1:05 - Minor Diameter 1:13 - Pitch Diameter 1:18 - Pitch 1:29 - Lead 1:36 - Flank Angle #Screw_Thread_Terminology #Angle_of_Thread #Metrology_and_Quality_Control This Video Topic is from Metrology and Quality Control Subject, you can also watch below mentioned videos related to Metrology and Quality Control Subject: Dial Gauge Indicator (Mechanical Comparator) -    • Dial Gauge Indicator Working | Mechanical ...   Sigma Comparator (Mechanical Comparator) -    • Sigma Comparator Working | Mechanical Comp...   Solex Pneumatic Comparator -    • Solex Pneumatic Comparator Working Princip...   Sine Bar (Angular Measurement) -    • Sine Bar Working Procedure | Angular Measu...   Bevel Protractor (Angular Measurement) -    • Bevel Protractor Working | Angular Measure...   Clinometer (Angular Measurement) -    • Clinometer Working | Angular Measurement |...   Autocollimator (Angular Measurement) -    • Autocollimator Working | Angular Measureme...   Profile Projector (Optical Comparator) -    • Profile Projector Working | Optical Compar...   Floating Carriage Micrometer (Screw Thread Measurement) -    • Floating Carriage Micrometer Working | Scr...   Screw Thread Terminology (Flank, Pitch, Root, Crest) -    • Screw Thread Terminology | Flank, Pitch, R...   Types of Screw Thread (V Thread, Acme Thread, Buttress Thread) -    • Types of Screw Thread | V Thread, Acme Thr...   Two Wire Method (Derivation of Effective Diameter for Thread Measurement) -    • Two Wire Method: Derivation of Effective D...   Three Wire Method (Derivation of Effective Diameter for Thread Measurement) -    • Three Wire Method: Derivation of Effective...   Best Wire Size (Screw Thread Measurement) -    • Best Wire Size in Screw Thread Measurement...   Parkinson Gear Tester (Gear Inspection) -    • Video   Gear Tooth Vernier Caliper (Gear Tooth Thickness Measurement) -    • Gear Tooth Vernier Caliper Working | Gear ...   Limit, Fit, Allowance and Tolerance -    • Limit, Fit, Allowance & Tolerance | Hole a...   Hole Basis System and Shaft Basis System -    • Difference Between Hole Basis System and S...   How to Solve Problems on Slip Gauge Set M87 and M45 -    • Problems on Slip Gauge Set M87 and M45 | H...   How to Solve Problems on Angle Gauge Set -    • Problems on Angle Gauge Set | How to Use A...   Faculty - Shubham Kola ( BE Mechanical Engineer ) Email ID - [email protected] From - Maharashtra ( India ) YouTube Channel ( Shubham Kola ) -    / @ifinfotech   Disclaimer - video is for educational purpose only. Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favour of fair use. The content in this video is collected from books, media, internet space etc. This is strictly for educational and information purposes and is not intended to be advice or recommendation of any kind whatsoever. The faculty is not a subject expert. The faculty is sharing his knowledge in the form of videos. The faculty giving small basics information on mechanical engineering topics. We endeavour to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the video or the information, related graphics contained in the video for any purpose. any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arise out of, or in connection with, the use of this video.