iPhone 17 Pro Disassembly & Reassembly | Housing Swap & Repair

Complete iPhone 17 Pro teardown! Replace frame, screen, battery, logic board, cameras, chassis, buttons & USB-C, back cover, then reassemble and calibrate with Repair Assistant. Buy tools and parts on AMAZON: Screwdriver Set: https://hfixt.com/spro Pro Toolkit: https://hfixt.com/tool Magnetic Mat: https://hfixt.com/mat Tweezers: https://hfixt.com/tzrs AliExpress: Adhesive tape: https://s.click.aliexpress.com/e/_c2x... Screwdriver Set: https://hfixt.com/alis Opening Tool Kit: https://hfixt.com/alit Magnetic Mat: https://hfixt.com/amat Tweezers set: https://hfixt.com/altz 📌*Useful links* Best Screwdriver Set:    • How to Choose the Best Screwdriver Set for...   Repair Tools & Safety Tips:    • Electronics Repair for Beginners: How to S...   More DIY repair guides: https://how-fixit.com 📱Follow us for more tech tips and guides! TikTok:   / howfixit   Instagram:   / howfixit   Facebook:   / howfixit   X: https://x.com/HowFixit Description In this HowFixit guide, I’ll completely disassemble the iPhone 17 Pro so you can replace any failed part: housing, screen, battery, logic board, cameras, Face ID, speakers, Taptic Engine, power/volume/control buttons, antennas, wireless-charging coil and the USB-C charging port. You’ll also see the full reassembly, calibration with Apple’s Repair Assistant, and water-resistance restoration using new adhesive sealing tape. 🔧Tools used: precision screwdrivers (Pentalobe 0.8, Tri-Wing 0.8, T4 Torx, Phillips 1.0, Standoff 1.5), plastic pry tools, tweezers, suction cup, screen disassembly tool, 9-volt battery with clamps (for battery adhesive release), magnetic mat, and adhesive sealing tape. Chapters below link to every step. If this helped, like & subscribe for more DIY repairs! 🎬Timecodes: 00:00 Intro & what you’ll learn 00:25 Tools & safety 01:14 Power off & remove Pentalobe screws 01:28 Heat display (90 °C / 194 °F) & create gap 03:24 Remove bracket & disconnect display 04:00 Battery plate: remove 14 screws 04:47 Battery removal (9-volt method) & adhesive tips 05:27 Install new battery adhesive 05:41 Face ID module: bracket, disconnect & remove 05:58 Rear cameras: 3 screws, disconnect & lift out 06:34 Earpiece speaker removal 06:53 Logic board: disconnects, coil cable, lift board 07:46 Flash diode & rear mic flex 09:45 LiDAR module removal 10:30 Removing the antenna 11:49 Removing the Taptic Engine 12:56 Bottom loudspeaker removal 13:31 USB-C charging port + lower mic flex removal 16:30 Volume buttons flex: screws & removal 17:05 Power & Control Button flex removal 18:42 Wireless-charging coil & back glass removal options 18:54 Frame/housing swap considerations 19:18 Reassembly best practices (screw mapping, connector cleaning) 33:29 Partial reassembly for boot test 33:51 Repair Assistant calibration (Parts & Service History) 34:16 Functional testing checklist (Face ID, cameras, buttons, audio, charge) 35:30 Restore water resistance: clean, apply new adhesive tape 39:15 Final assembly & closing tips 🌟FAQ: ❓Question: Will I get a “non-genuine part” message after replacing parts? ✔️Answer: Yes, iOS may show a notification in Parts & Service History. It doesn’t block usage; run Repair Assistant and verify functions. ❓Question: Do I need to recalibrate after camera, Face ID or housing changes? ✔️Answer: Yes. Use Repair Assistant via Settings - General - About - Parts & Service History and complete on-screen steps over Wi-Fi. ❓Question: How do I restore water resistance after opening the phone? ✔️Answer: Old adhesive loses sealing. Clean the frame with 91-99% isopropyl alcohol and apply a new pre-cut adhesive gasket before closing. AFFILIATE PROGRAM As an Amazon Associate, I earn from qualifying purchases. #iphone17pro #iphonerepair #teardown #ifixiphone #howfixit