✅ Дневник самостройщика: 9 правил при прокладке труб канализации в частном доме своими руками Проект

In this video, I'll try to cover the issues of sewer pipe installation when designing a sewer system for a private home as simply and clearly as possible - including slopes, diameters, rules and recommendations, etc. ✔ DIYer's Diary - 9 Sewer Rules ✔ DIY Sewer Pipe Installation in a Private Home - Slopes, Connections, Diameters ✔ Proper Sewer System Planning to Avoid Constant Cleaning and Eliminate Sewer Odors ✔ Video for DIYers - for those designing and installing sewer systems themselves ✔ Each connection to the sewer system (bath, toilet, sink, shower, etc.) must be made through a water seal to prevent sewer air from entering. ✔ A sewer odor entering a living space through the sink can be not only unpleasant but also toxic. ✔ The interior of the sewer system must be open to the outside air. ✔ A waste riser or waste pipe removes odors from a country house's sewer system through the roof to the street and prevents the water seal from failing (Bernoulli's law). ✔ The entire length of the pipeline must have a slope toward the riser to encourage waste to flow away by gravity. ✔ With a steep slope, the liquid will flow so quickly that it simply won't have time to pull solid waste down with it, resulting in inevitable clogs in the pipes. ✔ When designing sewer pipe layouts, slope markings typically begin from the riser. ✔ The socket of the waste pipes should increase, or at least NOT decrease, as each subsequent plumbing fixture is connected (a narrowing sewer socket almost guarantees clogs in the sewer system). ✔ The direction of the sockets: Sockets and pipes must face the flow (except for couplings). ✔ Access ports are installed for cleaning the pipeline. ✔ A plunger creates water hammer. ✔ An access port is designed so that any section of the sewer system can be accessed. ✔ Right angles are not recommended in sewer lines. If the design allows, it is better to use two 45º or three 30º angles instead of a 90º angle (especially when transitioning a horizontal section to a riser and when transitioning a riser to a horizontal pipeline). ✔ Check the difference in diameter between the pressure and non-pressure pipes: the non-pressure pipe diameter must be larger than the pressure pipe diameter. ✔ The toilet connection level should be lower than that of other plumbing fixtures, otherwise waste from it may appear in other drain holes. DIY DIYer's Diary - From an Apartment to Your Home! In this video, I will simply and clearly answer the questions of laying sewer pipes when designing a sewer system of a private house ✔ diary of a self-builder - 9 rules of sewerage ✔ laying sewer pipes in a private house with your own hands - slopes, connections, diameter ✔ competent planning of the sewerage system so that you do not have to constantly clean and that there are no sewer odors in the house ✔ designing and laying sewers with your own hands ✔ the connection of each consumer to the sewer (bathroom, toilet, sink, shower, etc.) must be made through a water lock to protect against the penetration of sewer air ✔ the smell from the sewer entering the living room through the sink is not only not pleasant, but also poisonous ✔ the internal space of the sewer must communicate with atmospheric air ✔ fan riser or fan pipe removes odors from the sewer of a country house through the roof to the street and avoids the breakdown of the water lock ✔ the pipeline along its entire length should have a slope in the direction of the riser so that the tend wastes to leave by gravity ✔ with a large slope, the liquid will fly so fast that it simply will not have time to pull solid waste behind it, as a result, blockages in pipes are inevitable the marking of the slope when designing the laying of sewer pipes usually starts from the riser ✔ the socket of the sewage pipes should increase or at least NOT decrease as each subsequent plumbing appliance is connected in the direction of the sockets: the sockets and pipes should be directed towards the current (except for the couplings) ✔ Revisions are installed to clean the pipeline ✔ Water hammer ✔ the revision is designed in such a way that there is access to any part of the sewerage system ✔ right angles are not recommended in the sewer wiring - if the design allows, it is better to make two 45° or 3 30° instead of a 90° angle ✔ the diameter of The non-pressure pipe must be larger than the diameter of the pressure pipe. ✔ The connection level of the toilet bowl should be lower than the rest of the plumbing equipment, otherwise waste from it may appear in other drain holes. #DIYDiary #WaterHarm #WaterTrapBreak #SewerRules #SewerAtHome #DoItYourself #DIY #SewerAtHome #SewerCleaning #SewerInspection #VentRiser #VentPipe #PipeSlope #PipeDiameter