FULL Guide! 2008-2013 Nissan Rogue AWD Front Control Arms and CV Axles

Replacing the front CV axles and lower control arms on your 2013 Nissan Rogue SV AWD? In this step-by-step DIY video for the first-generation Nissan Rogue (2008-2013), I walk you through the entire process from start to finish — with torque specs, tool callouts, and close-up footage that shows exactly what to expect. Whether you're dealing with torn CV boots, worn ball joints, or just want a smoother ride, this guide has you covered. ⚠️ This is for the first-generation Nissan Rogue (2008–2013) — AWD model shown. FWD is similar but may differ in axle length and disconnect steps. Repair Manual I used: https://www.emanualonline.com/cars/ni... My code METALOOP22 will save you 22% off your first purchase! What you'll learn in this video: 0:00 - Intro & Overview 1:01 - Symptoms: Clicking CV joints, loose front end 2:03 - Shop Manual 2:53 - Lift Points 3:30 - Wheel removal and fastener locations 4:08 - Disconnect ball joint and control arm bushings 5:35 - CV axle nut, shaft and seal Removal 7:36 - CV axle replace seal, shaft, axle nut 12:28 - Passenger Side control arm removal 14:05 - CV Axle Removal on Passenger side 15:20 - Passenger CV shaft seal removal and install 16:40 - Install new passenger CV Axle 17:24 - Install passenger control arm 19:36 - Refill transmission fluid steps Credits: Content Production - Shane G @ SRGKustoms Tools list for Nissan Rogue Front Control Arms and CV Axles ------------------------------ My Mid-Rise Scissor Life: https://amzn.to/4cFwYQ1 Ratchets 3/8" and 1/2" - https://amzn.to/4fG54DU Sockets 10, 18, 19, 21, 32 Impact Wrench - Flex Mid-Torque Impact Kit: https://amzn.to/42J1rJH Gearwrench Lugnut Impact Socket Set - https://amzn.to/3Y1Twno Hex Bits - 6mm Heavy Hammer Rubber Mallet / Dead blow Pliers, Diag Cutters My torque wrench recommendation: https://amzn.to/48Ne5J4 Suspension Strut Spreader Tool: https://amzn.to/44nsJXm Sunex Rolling Head Pry Bar Set (or Harbor Freight): https://amzn.to/3RhT7tZ Hammer-Ready Pry Bars: https://amzn.to/42bZSnr Premium Mini Grease Gun (or cheaper HF version): https://amzn.to/4lxeky0 Lucas Red & Tacky Grease Cartridges: https://amzn.to/4lu0Jr1 2008-2013 Nissan Rogue SV AWD Parts Used (Amazon affiliate links) ----------------------- CV Axles -Driver’s Front CV Axle (TrakMotive NI-8348): https://amzn.to/41afLZR -Passenger’s Front CV Axle (TrakMotive NI-8347): https://amzn.to/4gWD7bf Control Arms -Driver’s Side Control Arm (Mevotech CMS30194): https://amzn.to/4hLWoxt -Passenger’s Side Control Arm (Mevotech CMS30195): https://amzn.to/4hLtxZW Transmission Shaft Seals -Driver’s Side Seal (National 710598): https://amzn.to/4h1EFks  Alternative: SKF 15709 — https://amzn.to/4hJAOtg -Passenger’s Side Seal (SKF 12912): https://amzn.to/4hMHXJu STP Automatic Transmission Fluid STPCVT1QT If you purchase anything because of this video, let me know with a comment below to let me know my video was helpful. Thank you! 2008 - 2013 Nissan Rogue AWD Control Arm and CV Axle Torque Specs ------------------------ Driver Side -Steering Knuckle to Control Arm: 46 ft-lbs - 18 mm socket & wrench -Rear Bushing: 104 ft-lbs - 19 mm socket & wrench -Tube Bushings (x2): 126 ft-lbs - 21 mm -Sway Bar Link: 62 ft-lbs -18 mm & 6mm hex bit -Axle Nut: 136 ft-lbs - 32 mm -Wheel Speed Sensor Bolt: 7 ft-lbs - 10 mm -Lug Nuts: 81 ft-lbs - 21mm socket Passenger Side -Steering Knuckle to Control Arm: 46 ft-lbs - 18 mm socket & wrench -Rear Bushing: 104 ft-lbs - 19 mm socket & wrench -Tube Bushings (x2): 126 ft-lbs - 21 mm -Sway Bar Link: 62 ft-lbs -18 mm & 6mm hex bit -Axle Nut: 136 ft-lbs - 32 mm -Wheel Speed Sensor Bolt: 7 ft-lbs - 10 mm -Retaining Plate Bolts: 14–18 ft-lbs -Wheel Lug Nuts: 81 ft-lbs - 21mm socket Extra Tips ---------------------- -You can loosen axle nuts before lifting the vehicle. -Be gentle when removing the seal, don't damage the sealing surface. -Don't forget to check and add CVT fluid when installing new CV axles and shaft seals. -Always get an alignment after replacing suspension components.