MiniMod 6U Full System 'Berlin School' style performance - Melodic Eurorack Modular - AJH Synth

2-Voice 'Berlin school'-style performance, and first of a few videos featuring the same module lineup from the new MiniMod 6U Full System, now available to purchase from https://ajhsynth.com/Minimod.html, pre-installed in a powered case. This is an example of what is possible using just single, modest-sized case, packed with an incredibly flexible, vintage-voiced, fully analogue, Eurorack modular synthesizer. Here the synth is configured as two operate voices - a 2 VCO drone synth, and a single VCO with 2 sub oscillators lead synth. It uses all the modules from the Minimoog-based part of the system, along with the Gemini 2412 SEM-based dual VCF, and the indispensable Ring SM mixer, sub-bass generator and ring modulator. There's a patch sheet/diagram at the end of the video, along with patch notes and link to the patch PDF at the bottom of this description. The AJH SYNTH Eurorack range consists of high-end modules, all hand-made in the UK, most of which are based on classic, vintage designs, authentically recreating the circuitry of much sought-after analogue instruments and technologies of the past, whilst greatly expanding them, and bringing them to modern Eurorack levels of convenience, limitless flexibility, and reliability. Video by @DreamsOfWires More videos: NEW Full Systems Available Now:    • NEW! AJH Synth Complete Systems - 6U & 9U ...   NEW MiniMod Keys Available Now:    • AVAILABLE NOW! MiniMod Keyz Complete Syste...   NEW Triple Cross fader/panner:    • TRIPLE CROSS - Voltage-controlled Crossfad...   Patch sheet PDF: https://kvisit.com/8AE/ioIH Patch Notes: Green and red dots show approximate pot and switch positions. Pots with both green and red dots show the position changes made during the performance. Pots and switches that do not have green dots are not used in this patch, and should be left at their zero or off positions. This is a very 'busy' patch aimed at maximising the use of modules. As such it would not be realistic to recreate it 100% accurately, as pot adjustments are represented here as images (no presets here!). Nevertheless, here are some notes, which along with the video might help explain some of it: Only one VCO is controlled by the keyboard/sequencer, the others are free-running. I'm using D-FCV with the D-FCV Mix pot fully clockwise so that the connected CV only affects VCF2. This is so I can add a separate CV modulation signal to FCV2, without the need of a CV mixer to combine them. I then send the Red noise from the Glide + Noise module to FCV2. The triangle output of VCO1 goes to the Ring SM's X Input, so that this can be used by the module to generate sub-octaves. The sawtooth could also be used, and mixed into the audio, but the module tracks the triangle more successfully at high frequencies, whereas eventually it'll lose track of the sawtooth at high pitches. The 'OUT' output of the Precision Voltages is used for VCO3 with the switch in the A+B position, so that when the note or octave of A is switched it will also switch B by the same amount, and when B is switched it will only affect B. The DH-ADSR is looping with these settings, which will produce a kind of shark-tooth LFO waveform, since it's output is exponential, which is typical of an envelope generator.Green and red dots show approximate pot and switch positions. Pots with both green and red dots show the position changes made during the performance. Pots and switches that do not have green dots are not used in this patch, and should be left at their zero or off positions. This is a very 'busy' patch aimed at maximising the use of modules. As such it would not be realistic to recreate it 100% accurately, as pot adjustments are represented here as images (no presets here!). Nevertheless, here are some notes, which along with the video might help explain some of it: Only one VCO is controlled by the keyboard/sequencer, the others are free-running. I'm using D-FCV with the D-FCV Mix pot fully clockwise so that the connected CV only affects VCF2. This is so I can add a separate CV modulation signal to FCV2, without the need of a CV mixer to combine them. I then send the Red noise from the Glide + Noise module to FCV2. The triangle output of VCO1 goes to the Ring SM's X Input, so that this can be used by the module to generate sub-octaves. The sawtooth could also be used, and mixed into the audio, but the module tracks the triangle more successfully at high frequencies, whereas eventually it'll lose track of the sawtooth at high pitches. The 'OUT' output of the Precision Voltages is used for VCO3 with the switch in the A+B position, so that when the note or octave of A is switched it will also switch B by the same amount, and when B is switched it will only affect B. The DH-ADSR is looping with these settings, which will produce a kind of shark-tooth LFO waveform, since it's output is exponential, which is typical of an envelope generator. #eurorack #berlinschool #modularsynth