How to Build a Voron 2.4R2! - Step 16 First Print with Voron 2.4, Voron Test Cube!

In this step 16 of how to build a Voron 2.4r2, I print our very first print w/ the Voron 2.4 3D printer we just built, printing the Voron Test Cube with PETG. I go through slicer settings in detail along with some explanation of Printer.cfg. You can grab the Print start macro I use in SuperSlicer/Prusa Slicer here: https://3dprinterschool.com/print-sta... And also you printer.cfg here: https://3dprinterschool.com/voron-2-4... *Note - I don't like using print macro inside printer.cfg because you have to restart Klipper everytime you make changes. I like putting the print macro in my Slicer so I can easily change things on the go, especially when using different filaments.(e.g. I want to wait until enclosure is at least 37 degrees Celcius when printing with ABS but no wait for other filaments like PETG or TPU.) I spent hours trying to get other people's print macros working and never succeeded so I made my own, which I forked off my old Klipper stuff I used to use on my Ender 6. But it works for me and prints which is all I care about. Hopefully, it helps you too. There are a few random error messages but you can safely ignore them as they don't affect your prints. I did throw some random codes from many different sources to make it work. I haven't had the time to tidy my printer.cfg yet but will do soon! See All the Steps for How to Build a Voron 2.4R2 CoreXY 3D Printer: Step 1 Square Frame Assembly -    • How to Build a Voron 2.4R2! - Step 1 Squar...   Step 2 Bed Frame & Bottom Panel Assembly! -    • How to Build a Voron 2.4R2! - Step 2 Bed F...   Step 3 Installing Linear Rails -    • How to Build a Voron 2.4R2! - Step 3 Insta...   Step 4 Installing the Heat Bed -    • How to Build a Voron 2.4R2! - Step 4 Insta...   Step 5 Installing the Z Drives and Z Idlers! -    • How to Build a Voron 2.4R2! - Step 5 Insta...   Step 6 AB Drives and Idlers Assembly! -    • How to Build a Voron 2.4R2! - Step 6 AB Dr...   Step 7 Flying Gantry Assembly! -    • How to Build a Voron 2.4R2! - Step 7 Flyin...   Step 8 Z Joints & Gantry Install -    • How to Build a Voron 2.4R2! - Step 8 Z Joi...   Step 9 AB Belt Installation! -    • How to Build a Voron 2.4R2! - Step 9 AB Be...   Step 10 Afterburner Extruder/Hotend Installation -    • How to Build a Voron 2.4R2! - Step 10 Afte...   Step 11 How to Install Cable Chain/Chain Links! -    • How to Build a Voron 2.4R2! – Step 11 How ...   Step 12 Installing Wires thru Cable Chain! -    • How to Build a Voron 2.4R2! – Step 12 - In...   Step 13 How to Install Mainsail & Flash Klipper via USB DFU Mode! -    • How to Build a Voron 2.4R2! – Step 13 How ...   Step 14 Electric Wiring Step by Step! -    • How to Build a Voron 2.4R2! – Step 14 Elec...   Step 15 Klipper Setup, Probe as Virtual Z Endstop, Extruder Test! -    • How to Build a Voron 2.4R2! – Step 15 Klip...   Step 16 First Print with Voron 2.4, Voron Test Cube! -    • How to Build a Voron 2.4R2! - Step 16 Firs...