Installation for The Best 40W Laser Engraver——Sculpfun SF-A9 | Step by Step | Installation Tutorial

👉Subtitles are here: 【WIFI connection method 1】 Find the machine WIFI name Sculpfun SF-A9 XXX Initial password 12345678 Default IP address 192.168.4.1 【WIFI connection method 2】 😎For Windows: Download Sculpfun Laser Tool for Windows system And installation method 😎For Mac OS: First, enter the Official Sculpfun website and Select Windows Tools Download and install Sculpfun Laser Tool for Mac OS Since our software is still in a uploading review stage in the MAC store, use the following method to install first Enter the Sculpfun official website and select MAC Tools After downloading, enter the computer interface, click on Launchpad Open Terminal and enter 【sudo spctl -- master disable】 command Enter your computer's password. Note that the password will not be displayed, just press enter when finished! Open Security & Privacy in system settings, click on the "lock" in the lower left corner, choose to allow the app to be downloaded anywhere. 😎For Windows & Mac OS: Finally, open the downloaded installation package The use of the TOOL, take Windows System as an example After connecting the machine to the computer，Need to determine the COM of the engraving machine In computer management，Find the port corresponding to CH340，It's the COM of the engraving machine Enter your home WIFI name and password，Please note that only 2.4GHz WiFi is supported，Passwords do not support special characters Click to connect WIFI and disconnect the machine after obtaining the IP address Mobile phone and engraving machine connect to the same WiFi And enter the IP address obtained in the previous step to fill in the App 【BT connection method】 After connecting the engraving machine to the computer, open TOOL After switching to Bluetooth mode, turn on Bluetooth on the computer, and connect to the engraving machine After connecting the machine to the computer via Bluetooth, two ports will appear and you will need to try switching ports to connect until the connection is successful! Data cable connection method 【Switch AP mode】 After switching to AP mode，refer to APP connection method 1 to connect 【High and low speed switching】 The high-speed mode command is: $speed=1 The low-speed mode command is: $speed=0 【Connection and use of rollers】 Use the Sculpfun rotary roller, in the LightBurn settings, need to change "True" to "False" at $3 and "100" to "80" at $101. Note that when finished using it, please change the value to the original value! 【Cleaning and maintenance】 When the rollers are visibly dusty，To ensure engraving accuracy, timely cleaning is required When the guide rail is dirty, need to be cleaned and spray lubricating agent. Note that lubricating oil and lubricating grease are also suitable to use. When the engraving machine runs for a long time, the belt may be too loose, which will affect cutting accuracy Need to adjust the belt, left and right can not be too loose, and keep the tension as consistent as possible Loosen the synchronization shaft screws，Make the X-axis parallel to the front and rear frames. Adjust the left and right distances to be consistent Adjustable handle screw angle When the lens cannot be cleaned thoroughly, the spare lens can be replaced directly to ensure the machine performance.Note that the spare lenses can be purchased on the Official Sculpfun website. Can be cleaned with 75% alcohol Accelerated scene - move slowly --- ❤Purchase links for SCULPFUN SF-A9 40W❤ ▷tomtop: https://www.tomtop.com/p-osb0114eu.html ▷Allegro (Poland): https://allegro.pl/oferta/14698834225 ▷SCULPFUN Official Website: https://bit.ly/3st6lvf ▷Aliexpress: https://www.aliexpress.us/item/325680... ▷Geek buying: https://www.geekbuying.com/item/SCULP... ---- Subscribe Us: 👉Facebook：   / sculpfunofficial   👉Facebook Official Group：http://bit.ly/42q5rwO 👉TikTok: http://bit.ly/3lKPdgZ (@sculpfunreal) 👉Official Website: http://bit.ly/3ZDXd1j 👉Instagram：  / sculpfunofficial   👉Twitter:   / sculpfuntech   ------- Other videos in our channel you might be interested in: 👉Shorts for SF-A9 40W:    • Switch power in 1 second between 20W&40W! ...      • Cutting test by TJ Bell for SF-A9 40W on 1...      • 40W Laser Engraver Engraving on Ceramic Pl...      • Cut 15mm plywood in one pass!｜Replay of Wo...   👉Sculpfun iCube Laser Engraver | Best Desktop Laser Engraver | Perfect For Small Bussiness    • Sculpfun iCube Laser Engraver | Best Deskt...   -------- 0:00 Unpacking and installation 01:58 WIFI connection method 1 03:30 WIFI connection method 2 (For Windows & Mac os) 06:26 BT connection method 07:24 Data cable connection method 07:36 Switch AP mode 07:57 High and low speed switching 08:22 Connection and use of Sculpfun rotary roller 09:25 Cleaning and maintenance #sculpfunSFA9 #sculpfun #stepbystep #sculpfun40w #lasercutting #lasercutter #sculpfunlaser #smallbussiness #best40wlaser