Build THE BEST Tiny Whoop | The Easy Way

Thanks for watching ! As promised, below I've attached all the necessary links to either build your own race whoop or get one ready to fly from the Five33 shop! Want so support the channel? Consider shopping at Five33! Ready To Fly Whoop: ?utm_source=copyToPasteBoard&utm_medium=product-links&utm_content=web Parts Picker Page: https://flyfive33.com/pages/race-whoop Parts: Frame: https://flyfive33.com/products/meteor... AIO: https://flyfive33.com/products/betafp... Camera: https://flyfive33.com/products/c03-fp... Motors: https://flyfive33.com/products/betafp... Props: https://webleedfpv.com/collections/pr... Batteries: we bleed (ph 2.0) https://webleedfpv.com/collections/ba... https://pyrodrone.com/collections/1s-... VTX: https://flyfive33.com/collections/vtx... Tools T700 Glue: https://www.amazon.com/T-7000-Adhesiv... B600 Glue: https://www.amazon.com/Rhinestone-Adh... Phillips Driver: https://www.amazon.com/gp/product/B08... Mr.Chaus Drone Tune Esc settings 48khz PWM frequency Demag High version Betaflight / STM32F411 (S411) 4.4.3 Nov 14 2023 / 17:22:54 (738127e7e) MSP API: 1.45 config: YES start the command batch batch start reset configuration to default settings defaults nosave board_name BETAFPVF411 manufacturer_id BEFH mcu_id 003900393535510936323431 signature name: mrchaus feature feature -TELEMETRY serial serial 1 2048 115200 57600 0 115200 beacon beacon RX_LOST beacon RX_SET master set gyro_lpf1_static_hz = 500 set gyro_lpf2_static_hz = 1000 set dyn_notch_count = 2 set dyn_notch_q = 500 set gyro_lpf1_dyn_min_hz = 500 set gyro_lpf1_dyn_max_hz = 1000 set acc_calibration = -64,194,21,1 set min_check = 1010 set max_check = 1990 set rc_smoothing_auto_factor = 25 set rc_smoothing_auto_factor_throttle = 25 set blackbox_sample_rate = 1/2 set dshot_idle_value = 600 set dshot_bidir = ON set dshot_bitbang = ON set motor_pwm_protocol = DSHOT300 set motor_poles = 12 set vbat_max_cell_voltage = 438 set yaw_motors_reversed = ON set small_angle = 180 set pid_process_denom = 1 set simplified_gyro_filter_multiplier = 200 set osd_vbat_pos = 385 set osd_rssi_pos = 226 set osd_link_quality_pos = 2454 set osd_rssi_dbm_pos = 321 set osd_tim_1_pos = 2433 set osd_tim_2_pos = 406 set osd_flymode_pos = 374 set osd_throttle_pos = 2401 set osd_crosshairs_pos = 203 set osd_craft_name_pos = 2441 set osd_warnings_pos = 14353 set osd_avg_cell_voltage_pos = 2049 set osd_canvas_width = 30 set osd_canvas_height = 13 set vtx_band = 5 set vtx_channel = 8 set vtx_power = 2 set vtx_low_power_disarm = ON set vtx_freq = 5917 set gyro_1_sensor_align = CW90 set gyro_1_align_yaw = 900 set rpm_filter_harmonics = 2 set craft_name = mrchaus profile 0 profile 0 set dterm_lpf1_dyn_min_hz = 97 set dterm_lpf1_dyn_max_hz = 195 set dterm_lpf1_static_hz = 97 set dterm_lpf2_static_hz = 195 set vbat_sag_compensation = 100 set p_pitch = 69 set i_pitch = 74 set d_pitch = 64 set f_pitch = 175 set p_roll = 66 set i_roll = 70 set d_roll = 56 set f_roll = 168 set p_yaw = 66 set i_yaw = 70 set f_yaw = 168 set d_min_roll = 52 set d_min_pitch = 59 set feedforward_averaging = 2_POINT set feedforward_smooth_factor = 65 set feedforward_jitter_factor = 3 set feedforward_boost = 18 set simplified_master_multiplier = 140 set simplified_i_gain = 60 set simplified_d_gain = 125 set simplified_pi_gain = 105 set simplified_dmax_gain = 25 set simplified_dterm_filter_multiplier = 130 profile 1 profile 2 profile 3 restore original profile selection profile 0 rateprofile 0 rateprofile 0 set rates_type = BETAFLIGHT set roll_rc_rate = 90 set pitch_rc_rate = 80 set yaw_rc_rate = 70 set roll_srate = 70 set pitch_srate = 70 set yaw_srate = 70 set throttle_limit_type = SCALE rateprofile 1 rateprofile 2 rateprofile 3 restore original rateprofile selection rateprofile 0 save configuration