⚡ Power Up Your Knowledge! Free CSCS Test Prep (UK 2024): 43 Electrical Safety Q&A (Video 18)⚡

Free CSCS Test Practice Full 43 Questions And Answers UK. Electrical Safety-Tools & Equipment Video 18. Thank you for watching and GOOD LUCK FOR YOUR TEST . Please Don't Forget To Like, Share, Comment, And Subscribe To Support This Channel Recommended Books From Amazon Health, safety, and environment test for operatives and specialists 2019. https://amzn.to/3n5Hw1R Construction Health & Safety Awareness 2020 https://amzn.to/3BQTFxP CSCS Green Labourers Card Course Guide https://amzn.to/3v3G5V6 Recommended Personal Protective Equipment (PPE) Waterproof Safety Boot https://amzn.to/3HCDbfY Hi-Vis Jacket https://amzn.to/3DsjxAI Earmuffs, 30 dB, Green, Helmet Mounted https://amzn.to/30pkHyi Safety Gloves https://amzn.to/3kEYJPe Safety Industrial Goggles Anti Scratch Spectacles Glasses https://amzn.to/3kHm42L 0:00 Introduction 0:18 You need to work near an electric cable but the cable has bare wires. What SHOULD you do? Oive one answer 0:54 You are using a generator to power some lighting when a lamp blows. You have a spare lamp. What SHOULD you do? Give one answer 1:34 What are the two main visual inspections you should carry out before using a 2:28 What is BEST practice when using a power tool with a rotating blade? 3:05 What SHOULD be done before adjusting an electric hand tool 3:36 You have been asked to use a hand tool or power tool on site. You know that it is the right tool for the job. What else MUST you check? Give one answer 4:11 Why is it considered poor practice to store batteries loose in a tool bag? 4:44 When is it safe to work close to an overhead power line? 5:13 Questions. What SHOULD you do if the guard is missing from a power tool? 5:44 What SHOULD you do if the electrical equipment you are using cuts out? 6:15 Why should a residual current device (RCD) be used with 230 volt tools? 6:49 Which method is used to check if a residual current device (RCD) connected to a power tool is working? Give one answer 7:23 You need to use a 230 volt item of equipment. How SHOULD you protect yourself from an electric shock dive one answer 8:00 Why are battery-powered tools preferred over 110 volt tools in a construction environment? Oive one answer 8:28 What is the MAIN advantage of using battery-powered tools rather than electrical ones? Give one answer 9:02 Why do building sites use a 110 volt electricity supply instead of a 230 volt supply? Give one answer 9:35 What TWO things should you do to reduce trips and injuries caused by untidy leads and extension cables? Give two answers 10:29 Question 16. What TWO things should you do if you need to run an electrical cable across an 11:14 What TWO things should you do if you need to use an extension cable? Give two 11:56 What is the BEST way to protect an extension cable and also reduce trip hazards 7 Olve one answer 12:26 What SHOULD you do if an extension cable has a cut in its outer cover? Give one answer 13:03 Apart from dust, vibration, noise and flying fragments, identity another significant hazard in this image? Give one answer 13:21 What SHOULD you do if the head on your hammer becomes loose? 14:28 Do simple hand tools like trowels, screwdrivers, saws and hammers need to be 15:47 When do you need to check tools and equipment for damage? Give one answer 16:14 Question 2 If a power tool has a portable appliance testing (PAT) label on in what information should be included on the label? Give one answer 16:49 Question 23. Which item of equipment would NOT require portable appliance testing PAT? 17:21 You have been asked to dig to expose power cables. You have been given a cable avoidance tool (CAT) to detect them but you haven't been shown how to use it. What SHOULD you do? Give one answer 18:08 You need to use an air powered tool. What THREE hasards are likely to alect 18:48 If someone near you is using a petrol cut-off saw (disc cutter) to cut concrete 19:33 What does it mean if the equipment you are using is issued with a prohibition notice? Give one answer 20:09 Which TWO of the following statements about power tools are TRUE? Glve two answers 20:58 Why is in dangerous to run an abrasive wheel faster than its recommended MAXIMUM speed? Olve one answer 21:31 Why is it ESSENTIAL to be fully trained before using a cartridge-operated tool? 22:10 Where is the BEST place for a portable Residual current device RCD to be fitted? Give one answer 22:48 Question 36. What colour is a 110 volt power cable and connector 23:12 Which requirement MUST be met before operating a power tool? 23:44 Residual current devices (RCOS) SHOULD have a mechanical trip test at which Intervals? Olve one answer 24:13 How to Residual current devices RCD werk? Give one answer 24:44 What are the TWO main functions of the guards on cutting and grinding machines? Olve two answers 25:31 Question 3. What is the recommended maximum voltage for electrical equipment on