ExpressLRS // The Most Complete And Detailed Guide To Flashing 2018 R9M/R9mm // How to Step By Step

00:31 Flashing radio with latest firmware. This is a must or the radio will not talk to the module. 2:09 Fixing SD card error due to version mismatch. 2:47 Creating a new ELRS model in radio and model setup. 4:51 Module modification. Soldering a 400-1000ohm resistor onto module board. 5:50 Installing ExpressLRS Configurator to your computer 6:27 Flashing R9 module bootloader 7:53 Dowloading ELRS Lua script 8:43 Building and flashing ELRS version firmware to R9 module using the ELRS configurator 10:57 Beer thirty 11:04 Flashing bootloader to R9mm receiver. Building smart port cable to flash bootloader 13:34 Preparing R9mm receiver for pass-through flashing. Installing in quad 14:16 Preparing betaflight settings before pass-through flashing 15:32 R9mm pass-through flashing 17:34 Checking R9 module / R9mm receiver connectivity. Important information about mode settings when using ELRS 18:53 Testing quad / First bench arming (no props) 19:02 Conclusion Open-TX companion download https://www.open-tx.org/2021/07/23/op... QX7 transistor telemetry mod YouTube video    • GetFPV Learn - FrSky QX7 Crossfire Mod   GetFPV transistor telemetry mod product page https://www.getfpv.com/tbs-taranis-q-... ExpressLRS Quick Start https://www.expresslrs.org/2.0/quick-... The ExpressLRS Configurator can be downloaded from the ExpressLRS Quick Start website CurryKitten's video is the video that inspired me to proceed with this mod. you can watch his video here    • Converting FrSky R9 modules and RX's to Ex...   ************************************************ My personal notes to keep this video organized. The video should closely follow these notes below ************************************************ Update opentx to 2.3xx -Download latest ver of opentx from opentx.org -Copy file to firmware directory on SD card -Turn radio off , then turn on in bootloader mode (Trim tabs in then Quick press power button) Select bootloader mode Load firmware Edit verion.txt to match In radio setup -Create new model named ELRS (ex) -navigate to Hardware page and set baud rate to 115200 if running qx7 -Turn ADC filter off -turn internal module mode off in model setup -select CRSF as external mode Must have transistor telemetry mod if using a qx7 Must install resistor mod on R9 module Download ELRS configurator from ELRS ************************ R9M module bootloader flashing and firmware version flashing ************************ Download tx module bootloader from ELRS -Copy to SD card in firmware directory -Flash to external module with module plugged into radio Compile tx module build in ELRS configurator. -Select frskyR9 -Select R9M -Select bind phrase -Click Build -Copy the generated file to SD card in firmware directory -Flash to External module with module plugged into radio. Download Lua script from tx build screen -Create ELRS directory on SD card -Copy Lua script to ELRS directory on SD card ************************* R9mm receiver bootloader flashing and firmware version flashing via pass-through ************************* Solder servo pigtail to rx per instructions Download rx bootloader from ELRS -Copy to firmware directory on SD card -Plug rx into smart port -Flash rx bootloader to external module Solder rx to free uninverted uart per instructions Connect to betaflight , -In ports tab, select the correct uart for serialrx -In config tab, select Serial based receiver and Select CRSF -Enable telemetry -In Receiver tab, Set RSSI channel to Disabled Check CLI to be sure that serialrx_half duplex and serialrx_inverted are both off Compile rx build in ELRS configurator Select frskyR9 Select R9mm / R9mini Select bind phrase Select com port Be sure to close betaflight and reboot quad to clear the com port Plug in to USB on FC Click build and Flash When progress window says " retry " the build is complete and waiting on the receiver to power up in order to complete the Flash process Plug in battery and the flash will proceed. *************************** Final checks on betaflight *************************** Connect to betaflight and check radio inputs , stick movements etc. In the modes tab , Arm mode must be channel 1 and set to the high position for arming.