Endwall Flashing Installation On A Metal Roof. EASY Installation Video Wall Flashing On Metal Roof

Step By Step Endwall Flashing Installation Instructions On A Metal Roof. Install Metal Roof Endwall Trim At The Sidewall. Installation Instructions For Endwall Trim On A Corrugated Metal Roof. This endwall flashing installation video will cover: 00:00 How to install endwall flashing for a metal roof 01:01 Cutting and finishing endwall flashing at the sidewall 01:26 How to cut metal with snips 01:52 Installing foam closures for endwall flashing 02:38 Overlapping endwall trim on a metal roof 03:20 How do I fasten endwall trim If you already have not purchased your corrugated metal roofing give us a chance to bid your job. Save 15% to 50% with our manufacturer direct pricing and great customer service. Inexpensive delivery anywhere within the United States. Visit Our WEBSITE westernstatesmetalroofing.com Visit our LEARNING CENTER westernstatesmetalroofing.com/learning-center Download Our Install Guides 7/8" Corrugated https://www.westernstatesmetalroofing... R Panel/PBR Panel https://www.westernstatesmetalroofing... Western Rib/7.2 Panel http://www.metalforroofing.com/docs/w... How To Install Endwall Flashing For A Metal Roof. Step By Step Guide When planning your metal roofing project, if you have metal roofing panels that are running up into a wall, you’re going to need to install endwall to help control where water flows to protect your structure. Before we begin here is a list of the steps that need to be taken. To begin, please note that if your roof has a sidewall condition, all sidewall trim must be installed prior to fastening the endwall. How To Cut And Finish Endwall Trim At The Sidewall 1. Measure the width of your sidewall trim. 2. On the endwall, mark the width of sidewall and draw a line to the corner of trim. 3. With metal cutting snips, cut along the traced line. How To Install Foam Closures For Endwall Flashing 1. Prior to fastening your endwall, double sided butyl tape should be placed 1” from the edge of the endwall. 2. Place the foam closure strips on top of the butyl tape 1” from the edge of the endwall trim 3. Apply silicone sealant to the top of the foam closures. 4. Next, apply silicone sealant on top of the sidewall where the endwall trim meets. How To Overlap Endwall Flashing 1. Before you begin this part, make sure your overlaps are a minimum of 6”. 2. Mark your trim on the hem side 6” from the end and ⅛” up from the hem. 3. With metal cutting snips, notch out the hem of the endwall by cutting along the traced line. 4. On the adjacent piece, pry open the hem of the endwall by 6” to allow it to slide into the notched piece. 5. Place silicone sealant at all overlaps. 6. The top section should slide inwards onto the lower section of notched endwall. How To Fasten Endwall Flashing 1. Pancake screws should be used to fasten the top section of endwall 1” from the edge and 12” on center 2. Lap screws should be used on the lower section of endwall 1” from edge following the path of the foam closures. Screws should fall on the high seams of your metal roofing panels approximately 12” on center. 3. Pancake screws should be placed on the top section on both sides of any overlaps. 4. Lap screws should be placed on the lower section on both sides of any overlaps on the high seams of your metal roofing panels. 5. Clean off all metal shavings. The shavings can easily rust overnight, staining your roof. FOLLOW US ON SOCIAL MEDIA: FACEBOOK: https://bit.ly/facebook-wsmr INSTAGRAM: https://bit.ly/instagram-wsmr TWITTER: https://bit.ly/twitter-wsmr LINKEDIN: https://bit.ly/linkinin-wsmr HOUZZ: https://bit.ly/houzz-wsmr PINTEREST: https://bit.ly/pinterest-wsmr YOUTUBE: https://bit.ly/youtube-wsmr