How to change a 02 oxygen sensor on F150 5.0 Litre (EP 146) Bank 1 Sensor 1

Step by step how to change a 02 oxygen sensor on F150 5.0 Litre Bank 1 Sensor 1 shot in HD. Published Nov 09, 2020 🎦 Video divided into skippable chapters below! 🎦 ☕🍩 If this video helped you & you would like to make a modest donation to the channel, why not buy me some coffee & donuts? https://paypal.me/unclemarksdiyauto?l... 🍩 ☕ Paid link: 🛒 USA Amazon product link: 🔧 02 sensor special socket: SEEN IN VIDEO: https://amzn.to/4blUNeS NOT USED BUT COULD WORK: https://amzn.to/4bi0nyV 🛒 YA-201 scan tool: Product link: https://amzn.to/3vZ7dZL 🔧 Flex head 3/8th ratchet: https://amzn.to/3eDYjbs or https://amzn.to/3BdkzAB 📓 Auto repair for dummies: https://amzn.to/3cjh6Fw Chilton repair manual 2004-2014 Ford pickups: N/A Haynes repair manual 2004-2014 Ford pickups: N/A As an Amazon Associate I earn from qualifying purchases. 🎦 SKIPPABLE CHAPTERS 🎦 0:00 unclemarks Diy video starts. 0:55 P0030 Code explained. 1:10 P0030 code scanned on Ford F150. 1:39 P0030 code explained. 2:14 Where is Bank 1? 2:40 Where is sensor 1? 3:33 What a 02 sensor and socket tool looks like. 4:41 Where is sensor 1 bank 1 on the catalytic converter? 5:20 How to unhook wires on sensor 1 02 oxygen sensor. 6:20 How to undo the clip and connector on a 02 sensor. 7:12 How to undo the clip on a oxygen sensor 02 sensor. 7:50 What the o2 oxygen sensor clip looks like. 8:20 No room for your hands. 8:31 I get dirt in my eyes! 9:00 I use a small screw driver to pry 02 connector clip. 9:55 How to use a 02 socket on a oxygen sensor. 10:57 How to get the 02 socket on the sensor. 13:20 Fighting with a ratchet and failing! 13:50 Jacked the truck up higher for more room underneath. 14:07 How to get some leverage on a ratchet. 16:30 Using another tool since not enough space to remove with proper tool. 17:05 Success clamping on to 02 sensor! 18:10 Loosening sensor and wire issues. 18:20 How to remove a 02 sensor by spinning the wire once loose. 19:30 Sensor finally comes out! 19:50 How to install a 02 sensor. 21:10 Unclemarks comment if you think the video is getting too long! 22:15 Is there a special tool to install a 02 sensor? 23:45 How to slip the 02 socket over sensor. 27:12 How to attached the 02 cable back up with no room for your hands. 28:30 How to plug the 02 sensor back into the harness. 29:18 What tools do you need to replace a 02 sensor oxygen sensor? 29:40 What a old 02 sensor looks like. 30:15 Taking the truck off the jack stand. 30:35 Clearing codes before test drive. 31:18 Did the check engine light go out? 31:30 Test drive after new 02 sensor. 33:56 Ending thoughts and instructions. 34:50 The part number for 02 sensor I used in this video. (Check for your application first. 36:00 Little dog shows you to ring the bell twice to get all notifications. 36:25 Unclemarks diy Bloopers and out takes. ⚠️ Disclaimer: Due to factors beyond the control of unclemark, I cannot guarantee against improper use or unauthorized modifications of this information. Unclemark assumes no liability for property damage or injury occurred as a result of any of the information contained in this video. Use of this information is at your own risk. Uncle Mark assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Unclemark recommends safe practices when working on vehicles and or with tools, lifting tools, jacks and or jack stands, chemicals and or lubricants or anything else seen or implied in this video. Due to factors beyond the control of unclemark, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or lost that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not of unclemark. 🛒 -Links on this video to products are for informational purposes only and in no way are a endorsement of the safety or effectiveness of the particular product. 🔧 You should consult a qualified mechanic for your repairs. Statements made in this video are not intended as mechanical advice.