✅ Installation piscine | Raccord piscine | Tuyau PVC

As a bonus to this video 🎁: Here are 14 tips and tricks to ensure your assembly is a success the first time and to avoid common pitfalls that could cost you time and money: #1: Check the diameter of your pipes (50mm or 63mm) to buy the right materials for your installation. #2: Use PN10 or PN16 PVC pipes and fittings (pressure resistant). #3: Drain the pipes before disassembly. #4: Apply Teflon tape in the direction of the threads. Don't hesitate to be (very) generous! #5: Perform a complete assembly without glue to ensure the pipes are cut correctly. #6: Mark the different components for proper positioning during gluing. #7: Sand the fittings to be glued, perpendicular to the direction of water flow. #8: Clean the surfaces with a dry cloth, then with a little rubbing alcohol, before gluing. #9: Apply the glue, in the direction of water flow, to the two parts to be joined. #10: When gluing, fit the two parts together without rotating them, and let them dry for 10 minutes without moving them. #11: Remember to insert the rings if necessary before gluing. #12: During final assembly, remember to properly position the O-rings. #13: Refill the pool at least 1 hour after the final gluing. #14: Watch this video again before starting! 😉 Find the most reliable PVC pool glue on the market here: https://amzn.to/2PHIGDW 👉Pool Maintenance Store is here: https://www.amazon.fr/shop/entretienpi0b Here's a small collection of useful links to get the necessary materials for 50mm pipes: Opaque rigid pipe: https://amzn.to/2QODdf5 Transparent rigid pipe (the one in the video): https://amzn.to/3vEduVv Semi-rigid pipe: https://amzn.to/3xDWeBt 45° elbow (for less pressure loss): https://amzn.to/3vyRtHE 90° elbow: https://amzn.to/335ca1B Non-return valve (to keep the pump primed): https://amzn.to/3ue2EVN Screw fitting for the pump (2" thread): https://amzn.to/3xDwTYd Screw fitting for the sand filter (1/2" thread): https://amzn.to/3nCC3PL Union fitting (to add a screw fitting to a pipe): https://amzn.to/3eItkHS Manifold (3 to 1): https://amzn.to/3nH5DUq Valve (tap): https://amzn.to/3xFUnMj Coupling (for connecting to a cut pipe): https://amzn.to/3u9z7wB Bypass kit (for installing a heat pump): https://amzn.to/3nFgkGI PTFE Teflon sealing tape: https://amzn.to/3nFAeBO O-ring: https://amzn.to/333g7Uz ***** Summary: 00:00 Introduction 00:46 Listing the necessary materials 01:37 Dismantling the old installation 02:34 How to install a threaded fitting? 03:30 Cutting and dry fitting 04:40 Preparing the parts to be glued 05:27 Identifying the parts to be glued 05:52 How to glue a pool fitting? 07:37 Installing the new piping 08:18 Refilling the pool 09:50 Conclusion ***** My installation setup: In-ground pool / equipment room above the waterline. Connected management system: https://www.oklyn.fr Manual chlorine treatment. ***** Let's stay in touch 🙂: For more pool tips and tricks, subscribe:    / @entretienpiscine   Email: [email protected] I hope you enjoy this video and find it helpful. Share / Like / Comment! Thank you and see you soon. As an Amazon Associate, I earn from qualifying purchases. #PoolMaintenance | #PoolTips | #PoolPipes | #DIY