Class II composite restoration (1) – Slanting/oblique incremental technique (#16) - Arabic عربي

Class II composite restoration using the slanting/oblique incremental technique on a maxillary molar To learn about class II cavity preparation for composite on a maxillary molar, watch the video:    • Class II cavity preparation for composite ...   To learn about Enamel & dentin bonding / adhesive systems (3-step, 2-step, 1-step) & application, watch the video:    • Enamel & dentin bonding / adhesive systems...   To learn about class I composite restoration using the horizontal incremental technique, watch the video:    • Class I composite restoration (1) – Horizo...   To learn about composite cavity preparation & restoration instruments and tools setup, watch the video:    • Resin composite cavity preparation & resto...   To learn about finishing & polishing tools & application for class I & II resin-based composite restoration, watch the video:    • Finishing & polishing tools & application ...   To learn about how to check occlusion after restoring a cavity preparation, watch the video:    • Finishing & polishing tools & application ...      • How to check the occlusion? - Arabic عربي   Subscribe for more Preclinical Operative Dentistry videos:    / @drafnanoalzain   Music: https://www.bensound.com --- Contents of this video --- 00:00 – Introduction 00:14 – Title: Class II resin-based composite restoration – Slanting/oblique incremental technique (Mandibular first molar) 00:24 – Class II resin-based composite restoration – Slanting/oblique technique 00:48 – Place the matrix band & wedge 01:33 – Check that the gingival margin is sealed using a dental explorer 01:43 – Apply the adhesive system (One-step self-etch system), Selective enamel etching technique: a. Acid etch (enamel only) 02:36 – Apply the adhesive system (One-step self-etch system), Selective enamel etching technique: b. Self-etch adhesive (E+P+B) 03:16 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): a. Adapt in the floor 05:13 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): b. Remove excess using a dental explorer held at 45 degrees 05: 36 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): c. Light-cure 05:50 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): d. Place the following increment. e. Create the marginal ridge 07:31 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): f. Remove excess using a dental explorer held at 45 degrees BEFORE curing 08:58 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): g. Light-cure 09:09 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: a. Apply and adapt an increment (Slanting/oblique increment on part of the cavity) 10:15 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: b. Light-cure 10:22 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: c. Apply and adapt the following increment 11:02 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: d. Create anatomy 12:24 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: e. Light-cure 12:29 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: f. Add increments and create anatomy as needed 13:09 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: g. Light-cure 13:22 – Check the restoration margins for gaps, ditches, and excess 13:29 – Remove the matrix band and wedge 14:34 – Flake off excess bonding 15:05 – Additional curing proximally from the buccal and lingual directions AFTER matrix band removal 15:29 – Constantly clean the hand instruments as you are using them with alcohol swab 15:54 – Finishing and Polishing: Finishing: Proximal margins using #12 scalpel blade 16:31 – Finishing and Polishing: Finishing: Using diamond points with water coolant 19:13 – Finishing and Polishing: Finishing: Check the marginal ridge height, contour, contact, no overhang, margins, anatomy, and surface texture 19:28 – Finishing and Polishing: Finishing: Using diamond points with water coolant 19:57 – Finishing and Polishing: Finishing: Check the marginal ridge height, contour, contact, no overhang, margins, anatomy, and surface texture 20:03 – Finishing and Polishing: Finishing: Using diamond points with water coolant 20:33 - Finishing and Polishing: Finishing & Polishing Strips: used BELOW the contact area in “S” or sawing motion 21:55 – Finishing and Polishing: Polishing: using rubber points with water coolant 22:29 – Check the marginal ridge height, contour, contact, no overhang, margins, anatomy, and surface texture 22:43 – Check the contact 22:54 – Check the marginal ridge height, contour, contact, no overhang, margins, anatomy, and surface texture 23:41 – Check occlusion Instagram: @afnanalzain Twitter: @afnanalzain Telegram Channel: Dr. Afnan O. Al-Zain / t.me/afnanalzain Email: [email protected]