東京マルイ【P90】ジャンク復活計画その1！メカボックス組み直しで動作快調ですがパーツ欠品があって撃てません！スタンダード電動ガンは初体験なので楽しいです！PlasticModel-AirSoft

[S-san] Donation! This is the first part of a project to somehow revive Tokyo Marui's standard electric gun [P90] (junk)! This junk P-chan has a blown fuse and the red dot sight has been removed (tears) I'm going to repair it so that it can be used. [Kuroneko YZ Twitter account]   / kuroneko_yz   I don't tweet much, but please follow me! [Things I want!! (Amazon wish list)] https://www.amazon.jp/hz/wishlist/ls/... I would be very grateful if you could support me! [Reception of support supplies (Yamato Transport Center pick-up and shipping)] If you would like to support us, please send an email to "[email protected]". [Related videos] -Tokyo Marui [P90] High Cycle Project - Part 1! I tried using LayLax metal bearings! Customizing a standard electric gun, airsoft guns are deep! PlasticModel-AirSoft    • 東京マルイ【P90】ハイサイクル計画-その1！LayLaxメタル軸受け使ってみた！ス...   ・Tokyo Marui [P90] High cycle plan - Part 2! Refresh the wiring by changing to a 20A flat fuse, re-stretching the 2SQ cable, and changing to a T-shaped connector! Preparation for motor replacement! PlasticModel-AirSoft    • 東京マルイ【P90】ハイサイクル計画-その2！20A平型ヒューズ化・2SQケーブル張...   ・Tokyo Marui [P90] High cycle plan - Part 3! What will happen with a super cheap Li-Po battery? ? What is the discharge capacity of a Li-Po that costs just over 2,000 yen on Amazon! PlasticModel-AirSoft    • 東京マルイ【P90】ハイサイクル計画-その3！激安リポバッテリーでどうなる？？アマゾ...   ・Tokyo Marui [P90] High cycle plan - Part 4! I tried replacing the motor of an electric gun! How does the cycle change when I just install the EG-30000HC? PlasticModel-AirSoft    • 東京マルイ【P90】ハイサイクル計画-その4！電動ガンのモーター交換やってみた！EG...   ・Tokyo Marui [P90] High cycle plan - Part 5! Introducing the SHS [16:1] gear set・ Tried cutting the sector gear! Preparation for gear replacement・Checking operation inside the gearbox・Until it works properly! PlasticModel    • 東京マルイ【P90】ハイサイクル計画-その5！SHS【16:1】ギヤセット導入・ セ...   ・Tokyo Marui [P90] Junk revival plan Part 1! Reassembled the gearbox and it works fine, but it can't be fired because there are missing parts! It's my first time touching a standard electric gun, so it's fun! PlasticModel-AirSoft    • 東京マルイ【P90】ジャンク復活計画その1！メカボックス組み直しで動作快調ですがパー...   ・Tokyo Marui [P90] Junk revival plan Part 2! A quick fix to the chamber (lol) I forcibly fixed the hop-up gasket area, which was full of missing parts, with parts I had on hand! PlasticModel-AirSoft    • 東京マルイ【P90】ジャンク復活計画その2！チャンバー応急テキトー処置（笑）欠品だら...   -Tokyo Marui [P90] Junk revival plan part 3! Muzzle velocity in the 80m/s range! I replaced the entire original chamber with a good one and the performance came back! PlasticModel-AirSoft    • 東京マルイ【P90】ジャンク復活計画その3！初速80ｍ/s台！純正チャンバー一式を良...   -Marui [P90] Junk revival plan part 4! I got the original dot sight, rail, and receiver on Yahoo! Auctions and brought the P-chan back to its original form! I'm pouring so much money into it that I can buy a good used item (lol) PlasticModel-AirSoft    • マルイ【P90】ジャンク復活計画その4！ヤフオクで純正ドットサイトやレールやレシーバ...   ・Marui [P90] Junk Restoration Plan Part 5! I tried out the super cheap LONEX chamber gasket! It comes with a ring and is a reasonable price, but what about the initial velocity, accuracy, and performance? PlasticModel-AirSoft    • マルイ【P90】ジャンク復活計画その5！激安LONEXチャンバーパッキン試してみた！...   ・Marui [P90] Junk Restoration Plan Part 6! I tried installing a FET! Made by XCORTECH for 1350 yen, prevents trigger terminals from burning and improves response! It's a simple soldering job! PlasticModel-AirSoft    • マルイ【P90】ジャンク復活計画その6！FET取り付けてみた！XCORTECH製13...   ・Marui [P90] Junk Restoration Plan Part 7! LayLax-EG spring guide/smoother increased muzzle velocity and cycle! LayLax PROMETHEUS PlasticModel-AirSoft    • マルイ【P90】ジャンク復活計画その7！LayLax-EGスプリングガイド/スムーサ...   -Marui [P90] Junk revival plan #8! Tried the HurricanE NB cylinder SET! Muzzle velocity may have dropped (lol) PlasticModel-AirSoft    • マルイ【P90】ジャンク復活計画その8！HurricanE（ハリケーン）NBシリンダ...   -Marui [P90] Junk revival plan #9! Installed LayLax non-liner spring MS90! This may be boring with a simple muzzle velocity comparison video! Muzzle velocity will definitely increase! Laylax-PlasticModel-AirSoft    • マルイ【P90】ジャンク復活計画その9！LayLaxノンライナースプリングMS90組...   -Marui [P90] Junk Restoration Plan Part 10-Muzzle velocity finally exceeded 95m/s! Changed to [CNC piston]! Problems discovered with custom parts assembled last time! PlasticModel-AirSoft    • マルイ【P90】ジャンク復活計画その10-ついに初速95m/s越えた！【CNCピスト...   -Marui [P90] Junk Restoration Plan Part 11! Shim adjustment brought cycle back! Tried using Laylax Prometheus shim set! Reduced friction loss in gearbox! PlasticModel-AirSoft    • マルイ【P90】ジャンク復活計画その11！かんたんシム調整でサイクルが戻った！ライラ...   -Marui [P90] Junk Restoration Plan Part 12! Barrel replacement caused too much muzzle velocity!! Adjust with spring! Uses a super cheap 6.03mm tight barrel for 1800 yen! PlasticModel-AirSoft-ToyGun    • マルイ【P90】ジャンク復活計画その12！バレル交換で初速が出すぎ！！スプリングで調...   -Marui [P90] Junk revival plan part 13! Accuracy and ballistic check (gun camera style) and current custom...