🎀 TUTO #DIY RAPIDE & FACILE 🎀 Coudre pas-à-pas L' Étui à Lunettes ZIPPÉ #FIDJI 🥰

Super Easy DIY Tutorial: Quick Step-by-Step Sewing of a Zip-Up Glasses Case #FIDJI 🥰 The finished glasses case measures 20 cm high x 11 cm long 😊 🔅Links to my tools and supplies🔅 My sewing machine: https://amzn.to/3kLh90z My sewing machine table: https://amzn.to/3nCy3zq My 16 cm x 60 cm patchwork ruler: https://amzn.to/3qGrzSQ~ My 10 cm x 45 cm patchwork ruler: https://amzn.to/3Lnszpy My curved edge guide: https://amzn.to/3qx1y7G The heat-erasable pen: https://amzn.to/3oC1XUx Clips: https://amzn.to/3x2SidM Pinking shears: https://amzn.to/3CmWjL0 Sewing scissors: https://amzn.to/3HR3XkM Rotary cutter and cutting mat: https://amzn.to/3S5Jm2a Teflon foot: https://amzn.to/3snGrEW Presser foot: https://amzn.to/3XkcH9E Zipper foot: https://amzn.to/40ijdzt Pom-poms: https://amzn.to/3awWewt 🔆 Links to my fabrics 🔆 Outer fabric: https://eunitecidos.pt/loja/texteis/m... Lining fabric: https://eunitecidos.pt/loja/texteis/_... Lilac zipper: https://eunitecidos.pt/loja/cores/fec... Fuchsia slider: https://eunitecidos.pt/loja/retrosari... Bias binding: https://eunitecidos.pt/loja/cores/vie... Fusible stabilizer foam (4 mm thick) : https://eunitecidos.pt/loja/enchiment... ENJOY 5% OFF your entire order on the Eunitecidos haberdashery website by entering the code 👉🏻 Mélou5#Eunitecidos 🤩 (ps: enter the code in the designated box labeled "Coupon code," paying close attention to uppercase and lowercase letters...do not enter the code in the "Gift card number" box) 😘 Materials: -1 outer fabric, 30 cm long x 32 cm high -1 fusible interfacing, 30 x 32 cm -1 lining fabric, 30 x 32 cm cm -1 30cm zipper -1 slider -1 meter of bias tape Feel free to share photos of your creations directly on my Facebook group 👉🏻   / 482455733276472   🙏🥰💕💝 Thank you so much and happy sewing everyone! 😘💋❤ Chapters: 00:00: Introduction: A fully zippered glasses case that effectively protects your glasses (from sand, scratches, etc.). It's easy to make for the whole family. 00:44: Materials list: Outer fabric, fusible interfacing or foam, and lining (30 x 32 cm). A 30cm zipper, a slider, and approximately 1 meter of bias tape. 01:16: Quilting: Fuse the outer fabric to the interfacing. Draw lines every 2 cm along the entire height (32 cm) [01:24]. Assemble the outer fabric and lining (wrong sides together) and sew along all the drawn lines [03:29]. 03:55: Final trimming: Trim your quilted panel to the exact dimensions of 23 cm long by 27 cm high [04:04]. 05:06: Marking the point: On one side (27 cm high), mark a point 15 cm from the bottom. Connect this point to the opposite top corner to create a diagonal line and trim the excess [05:25]. 05:58: Attaching the bias binding and zipper: Measure the diagonal (approximately 26 cm) and attach the bias binding across this trimmed edge [06:40]. Then sew the zipper under the finished edge with the bias binding [07:25]. 07:53: Slider assembly: Separate the zipper into two sections. Align the fabric edges and insert the slider on both sides of the zipper to close the case [08:45]. Sew a small safety stitch at the end of the zipper [09:20]. 09:31: Case closure: Turn the case inside out. Carefully align the bottom and side edges, then sew 5 mm from the edge on both sides [10:22]. 10:31: Interior finishing: Apply bias tape to the seams you just sewed (bottom and side) to conceal the raw edges. Fold the ends of the bias tape neatly for a clean finish [10:53]. 11:51: Result: Turn the case right side out, making sure to push out the corners. Your case is now ready to hold and protect your glasses.