Sprinter Agile Off Road RIP Kit 2025 installation

Welcome to Only Vans! I’m Trevor, lead Sprinter Tech (@OnlyVansMB). In this video, I’m showing how to install the Agile off road RIP (Ride Improvement Package) kit on a 2023-2025 Mercedes Sprinter, this video is also helpful for 2022 and older though there are differences in the front suspension due to an updated subframe. My General Manager who's van this kit is done on has stated the ride quality is so much better over stock even before building the van out. I learned quite a few lessons while doing this install and did my best to highlight them with notes within the video so pay attention to those. I have replaced rear axles and replaced all suspension components on Sprinters but only with OEM. this is my first experience with aftermarket heavier duty upgraded rear leaf springs and secondary shocks Disclaimer: Always follow safety guidelines and consult your vehicle’s manual. Only Vans is not responsible for any damages resulting from improper application of this information. 0:00:00 - 0:00:26 intro 0:00:27 - 0:01:05 instruction QR code cards 0:01:06 - 0:01:35 What's in the kit 0:01:36 - 0:01:56 ride height before suspension install 0:01:57 - 0:03:23 Safely lifting front of vehicle 0:03:24 - 0:03:28 Mr. boss man! 0:03:29 - 0:03:46 Removing front wheels and tires 0:03:30 - 0:07:29 Removing front fender liners, pas speed sensor, test fit passenger upper mount, etc 0:07:30 - 0:09:42 Unbolting upper strut nuts 0:09:43 - 0:10:34 driver wheel speed sensor and rear fender liner portions 0:10:35 - 0:10:56 test fit upper driver shock mount 0:10:57 - 0:11:39 lock tight and locking nuts opinion 0:11:40 - 0:12:05 scribing knuckle for camber later 0:12:06 - 0:13:03 removing passenger front shock 0:13:03 - 0:13:42 moving passenger front brake out of working area to prevent brake line damage 0:13:43 - 0:13:58 removing passenger front shock continued 0:13:59 - 0:14:08 partial set up of coil over spring on new Bilstein's 0:14:09 - 0:23:24 Installing passenger front upper secondary shock bracket 0:23:25 - 0:26:50 Installing passenger front lower secondary shock bracket 0:26:51 - 0:31:35 installing passenger front secondary shock 0:31:36 - 0:39:34 setting up coilover spring on Bilstein shock and installing (passenger front) 0:39:35 - 0:40:26 reinstalling passenger front brake 0:40:27 - 0:45:43 installing passenger front fender liner and cutting to fit front portion 0:45:44 - 0:48:36 Installing passenger front wheel studs 0:48:37 - 0:49:46 Driver front secondary upper shock bracket rough fit 0:49:47 - 0:51:31 removing driver front shock 0:51:32 - 1:00:08 Installing driver front upper secondary shock bracket 1:00:09 - 1:02:03 Installing driver front lower secondary shock bracket 1:02:04 - 1:02:29 Removing incorrectly placed washers on passenger lower shock bracket 1:02:30 - 1:04:48 Installing driver side secondary shock 1:04:49 - 1:10:07 Installing driver side coilover shock and brake 1:10:08 - 1:11:33 Installing and cutting driver side fender liner 1:11:34 - 1:12:05 front suspension completed 1:12:06 - 1:14:03 instruction QR code cards (again lol) 1:14:04 - 1:16:38 safely lifting and securing rear of vehicle 1:16:39 - 1:17:14 removing rear wheels and tires 1:17:15 - 1:17:47 going over rear suspension parts 1:17:48 - 1:18:19 removing rear brake line brackets from leaf blocks 1:18:20 - 1:19:29 beginning removal of passenger factory leaf spring 1:19:30 - 1:20:54 removing spare tire 1:20:55 - 1:22:48 passenger rear leaf spring removal continued 1:22:49 - 1:23:00 important on screen note about only unbolting shock and sway bar on side being worked on 1:23:01 - 1:25:16 what happens if you unbolt shocks and sway bar links on both sides (oops lol) 1:25:17 - 1:26:28 unbolting parking brake cables and electrical lines from rear axle 1:26:29 - 1:27:38 passenger rear leaf spring removal continued (again) 1:27:39 - 1:28:27 pointing out my error and what i had to do to fix it 1:28:28 - 1:29:08 finally getting factory passenger rear leaf spring out 1:29:09 - 1:31:11 swapping shackle from factory leaf spring to agile upgraded leaf spring 1:31:12 - 1:39:42 Installing passenger agile leaf spring 1:39:43 - 1:40:08 noticing my passenger leaf spring saddle position issue 1:40:09 - 1:42:58 removing factory driver side rear leaf spring 1:42:59 - 1:44:47 swapping shackle from factory leaf spring to agile upgraded leaf spring 1:44:48 - 1:46:39 installing driver side agile leaf spring 1:46:40 - 1:47:53 final torqueing both rear leaf springs 1:47:54 - 1:49:35 installing passenger side rear upper shock bracket/reinforcement 1:49:36 - 1:51:00 installing driver side rear upper shock bracket/reinforcement 1:51:01 - 1:51:32 fixing passenger side shock bolt bracket alignment 1:51:33 - 1:56:36 installing both lower rear shock brackets 1:56:37 - 2:01:49 installing both rear shocks 2:01:50 - 2:05:15 finishing touches and brake line covers 2:05:16 - 2:09:36 rear studs, final measurements and outro. Thanks for watching!