How to replace the Lower Control Arms 2009-2018 Dodge RAM 1500 🚗

Find the parts used in the video on CarParts.com just there https://carparts.solutions/RAM1500 ⚙️ NEEDED CARPARTS AND PRODUCTS Lower control arms : https://carparts.solutions/LowerContr... and https://carparts.solutions/LowerContr... Penetrating oil Grease Silicone grease 💪 TIGHTENING TORQUES Link-to-control arm nuts : 75 Ft-lbs Link-to-stabilizer bar nuts : 20 Ft-lbs Tie rod end holding nut : 78 Ft-lbs Upper control arm ball joint : 40 Ft-lbs + additional 200 degrees Lower control arm ball joint nut : 37 Ft-lbs + additional 90 degrees Strut lower nut : 155 Ft-lbs Arm-to-frame pivot (alignment camber) bolts : 155 Ft-lbs Brake caliper mount bolts : 130 Ft-lbs Wheel hub nut : 185 Ft-lbs 🛠 TOOLS The toolbox recommended by CARPARTS.COM to repair your Dodge RAM 1500 : https://carparts.solutions/ToolBox List of the tools we used to replace the lower control arms on a Dodge RAM 1500 : Measuring tape Breaker bar 35mm socket Hydraulic jack : https://carparts.solutions/FloorJack Jack stands : https://carparts.solutions/JackStands Wheel lug wrench Clamp or iron thread Ratchet 21mm socket Fork Hammer Wire brush 24mm socket Marker 24mm wrench Plastic mallet Torque wrench : 20 to 250 Ft-lbs https://carparts.solutions/TorqueWren... 100 to 600 Ft-lbs https://carparts.solutions/TorqueWren... 12mm socket Flat head screwdriver Crowbar Don't forget to subscribe :    / @carpartscomofficial   🛻 COMPATIBLE VEHICLES The operation and tools displayed in the video should be available on the following vehicles : 2009 RAM 1500 2010 RAM 1500 2011 RAM 1500 2012 RAM 1500 2013 RAM 1500 2014 RAM 1500 2015 RAM 1500 2016 RAM 1500 2017 RAM 1500 2018 RAM 1500 📽 🛠 USEFUL VIDEOS 🛠 📽 How to jack your Dodge RAM 1500 safely :    • How to jack your 2009-2018 Dodge RAM 1500 ...   How to replace the Outer Tie Rod 2009-2018 Dodge RAM 1500 safely 🚗 :    • How to replace the Outer Tie Rod 2009-2018...   How to replace the Front Sway Bar End Links 2009-2018 Dodge RAM 1500 safely 🚗 :    • How to replace the Front Sway Bar End Link...   ⚠️ CARPARTS.COM'S INFOS Before lifting your vehicle, it is necessary to measure the distance between the centre of your wheel and the wheel arch. This will allow you to achieve an optimal tightening of the parts in their initial position. In order not to damage the silent blocks, it is necessary to tighten the front retaining bolts in the "vehicle on the ground" position. During this operation, you will be intervening on the front axle of your car, so it is advisable to perform a wheel alignment afterwards. 🚨 DISCLAIMER This video is for entertainment purposes only. Carparts.com, Inc. disclaims all damages including, but not limited to, actual, consequential, and/or punitive, for any liability, claim, or any other injury or cause related to or arising from any information or lack thereof posted in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All mechanical car projects entail some risk. It is the sole responsibility of the viewer to assume this risk. If you are in doubt, please consult a licensed mechanic in your area. 📚 CHAPTERS 0:00 Intro 0:18 Measure + loosen the wheel hub 0:38 How to pull up your RAM 1500 1:19 Remove the brake system 1:58 Disconnect some cables 2:21 Remove the control arms ball joints 2:54 Remove the outer tie rod 3:16 Remove the steering knuckle 3:51 Remove the sway bar end link 4:03 Remove the alignment camber bolts 4:44 Remove the strut foot 5:04 Remove the lower control arm 5:20 Clean the elements 5:33 Put the lower control arm back 6:08 Put the strut foot back 6:32 Put the sway bar end link back + tightening torques 6:54 Put the the steering knuckle back 7:41 Put the outer tie rod back + tightening torques 8:11 Tighten the ball joints + tightening torques 8:23 Tighten the strut foot + tightening torques 8:43 Tighten the camber bolts + tightening torques 9:07 Put the brake system back + tightening torques 9:47 Reconnect the cables 10:07 Replace the hub nut + tightening torques 10:31 Put your RAM 1500 back on the ground