Диагностика Nissan Micra/March K12 без сканера. Как сбросить ошибки на Ниссан при помощи педали

How to diagnose a Nissan without a scanner. The video shows instructions for CR12DE and CR14DE engines (Nissan Micra, Nissan Note, Nissan March), Nissan AD, and Nissan Cube. Diagnosing errors: (worked for me on the third try) 1. Make sure the accelerator pedal is fully released, turn the ignition key to the ON position, and wait 3 seconds. 2. Quickly repeat the following procedure 5 times within 5 seconds: — Fully depress the accelerator pedal. — Fully release the accelerator pedal. 3. Wait 7 seconds, fully depress the accelerator pedal, and hold it for about 10-15 seconds until the check engine light starts flashing. 4. Fully release the accelerator pedal. After 10 long flashes, the check engine light will flash quickly—the number of flashes is the number displayed. 10 blinks means 0. Resetting errors To reset the error, after the check light has completely cleared, press the accelerator and wait 10 seconds, then turn off the ignition. Trouble Codes: U1000 — ECM unable to communicate with other control modules U1001 — ECM communication period exceeded P0000 — No faults detected P0011 — Intake valve timing malfunction P0031 — Pre-catalytic Oxygen Sensor Heater Low Voltage P0032 — Pre-catalytic Oxygen Sensor Heater High Voltage P0037 — Post-catalytic Oxygen Sensor Heater Low Voltage P0038 — Post-catalytic Oxygen Sensor Heater High Voltage P0107 — MAP Sensor Low Voltage P0108 — MAP Sensor High Voltage P0112 — IAT Sensor Low Voltage P0113 — IAT Sensor High Voltage P0117 — ECT Sensor Low Voltage P0118 — ECT Sensor High Voltage P0132 — Pre-Catalytic Oxygen Sensor Low Voltage P0133 — Pre-Catalytic Oxygen Sensor Signal Recognition Time Too Long P0134 — Pre-Catalytic Oxygen Sensor Not Active P0138 — Post-Catalytic Oxygen Sensor High Voltage P0139 — Post-Catalytic Oxygen Sensor Signal Recognition Time Too Long P0171 — Fuel Mixture Too Lean P0172 — Fuel Mixture Too Rich P0221 — Throttle Position Sensor (TPS) Circuit Malfunction P0222 — TPS Sensor 1 Low Voltage P0223 — TPS Sensor 1 High Voltage P0226 — APP Sensor Circuit Malfunction P0227 — APP Sensor Low Voltage 1 P0228 - APP Sensor 1 High Voltage P0300 - Multiple Cylinder Misfire P0301 - P0304 - Cylinder Misfire #1-#4 P0327 - Knock Sensor Low Voltage P0328 - Knock Sensor High Voltage P0335 - CKP Sensor Circuit Malfunction P0340 - CMP Sensor Circuit Malfunction P0420 - Catalytic Converter Efficiency Below Acceptable Level P0444 - EVAP Canister Purge Control Solenoid Circuit Open P0500 - ECM Not Receiving Correct Signal from Vehicle Speed ​​Sensor (VSS) P0605 - ECM Malfunction P0705 - PNP Sensor Circuit Malfunction P0710 - ATF Temperature Sensor Voltage Too Low or Too High P0720 - TCM does not receive a valid signal from the VSS sensor P0725 — TCM does not receive a valid signal from the ECM P0731 — P0734 — AT cannot shift to 1st-4th gear respectively, despite the electrical circuit being normal P0740 — TCM detects a voltage drop when attempting to operate the torque converter clutch solenoid P0745 — TCM detects a voltage drop when attempting to operate the line pressure solenoid P0750/P0755 — TCM detects a voltage drop when attempting to operate the shift solenoid A or B, respectively P1065 — Malfunction in the ECM power supply circuit P1111 — Malfunction in the intake valve phasing control solenoid P1121 — Malfunction of the throttle actuator P1122 — Malfunction in the throttle actuator circuit P1124 — Short circuit in the throttle actuator relay circuit throttle actuator circuit P1126 — Throttle actuator relay circuit malfunction P1128 — Throttle actuator circuit short circuit P1143 — Pre-catalytic lambda sensor maximum and minimum output voltage values ​​do not reach the set limits P1144 — Pre-catalytic lambda sensor maximum and minimum output voltage values ​​exceed the set limits P1146/P1147 — Post-catalytic lambda sensor maximum/minimum output voltage values ​​do not reach the set limit P1171 — Fuel system error: MAP sensor output voltage excessively high P1217 — Engine overheating P1223 — TPS 2 voltage low P1224 — TPS 2 voltage high P1225 — Throttle position detection error (value too high) (low) P1226 - Closed Throttle Position Not Programmed P1227 - Low Voltage from APP Sensor 2 P1228 - High Voltage from APP Sensor 2 P1229 - Short in TPS Sensor Circuit P1610 - P1615 - NATS System Malfunction P1705 - TCM Receives Incorrect Signal