Artillery X2 und Genius PRO - TFT und Marlin Firmware full flash

Artillery X2 and Genius PRO - TFT and Marlin Firmware Full Flash #geniuspro #X2 #MoveInZ3Dprinting This new firmware gives you many new features for operating and calibrating your printer. In this tutorial, I'll guide you through flashing my mainboard with both Marlin and the new TFT firmware. With this new firmware, the Load/Unload menu and many other functions now work. You can find all the details of this firmware on the creator's Thingiverse page. Please check the current information BEFORE flashing. If flashing the display fails (the flashing process doesn't start), it's very likely because Artillery has recently switched to a different display – so there are currently different display types in circulation. ❗Addendum to the video❗ PrEzi informed me that the TFT firmware is also his. Sorry for the incorrect information. PrEzi informed me that the TFT firmware is also his. Sorry for the incorrect information. : ... ✏️Thingiverse Links: https://www.thingiverse.com/thing:518... STM32CubeMX Download https:https://www.st.com/en/development-too... Start code for Cura as mentioned in the video ;thanks to d3crypt0 G28 ; home all axes M155 S30 ; reduce temperature reporting rate to reduce output pollution G29 I4 P1 ; automatically populate mesh with all reachable points G29 P3 ; infer the rest of the mesh values G29 P3 ; infer the rest of the mesh values ​​again @BEDLEVELVISUALIZER ; tell the plugin to watch for reported mesh M420 S1 V ; enabled leveling and report the new mesh G29 S0 ; Save UBL mesh points to slot 0 (EEPROM). G29 F 10.0 ; Set Fade Height for correction at 10.0 mm. G29 A ; Activate the UBL System. M500 ; save the current setup to EEPROM M155 S3 ; reset temperature reporting ;M84 ;Disarm steppers M117 Purge extruder G92 E0 ; reset extruder G1 Z1.0 F3000 ; move z up little to prevent scratching of surface G1 X2 Y20 Z0.3 F5000.0 ; move to start line position G1 X2 Y200.0 Z0.3 F1500.0 E15 ; draw 1st line G1 X2 Y200.0 Z0.4 F5000.0 ; move to the side a little G1 X2 Y20 Z0.4 F1500.0 E30 ; Draw 2nd line G92 E0 ; reset extruder G1 Z1.0 F3000 ; move in z up a little to prevent scratching of surface ▬▬▬ ▬▬▬ ▬▬▬ Do you like what I do and want to support the channel? ☕ Buy me a coffee ;-) and click "$ Thanks" on one of the videos ☕ ☕ or via paypal.me/ThorstenDanner ☕ ⭐️ If you'd like to support the channel by becoming a member, you can find out more here ⭐️ ⭐️    / moveinz3dprinting   ⭐️ 👕 Shirts and more* https://shop.spreadshirt.de/move-in-z/ 🧢 **❤️ Thank you so much to everyone who has supported me so far ❤️** ▬▬▬ ▬▬▬ ▬▬▬ If you try to replicate anything shown in this video, you do so at your own risk - no liability is assumed. ++Advertisement+++ This video and description contain unpaid advertising. *For product links, I use affiliate links and receive a small commission if you purchase through one of these links, which benefits the channel. You do not pay a higher price when purchasing through these links. I was not paid by any company. 00:00 Introduction + Preparation 05:00 Flashing the Mainboard 11:05 Flashing the TFT Monitor 18:31 Calibrating PID, Steps, Offset 23:57 Important Information at the End