EPA Function on RC6GS V3 / RC4GS V3
How to Assign a Switch to Control EPA on RC6GS V3/ RC4GS V3? Power RC6GS V3 on. Long press Exit and Enter button at the same time to enter the setting page. -- No.3 EPA EPA is to set different travel amount of a servo on either side from its neutral position. SW means Switch. You can assign a switch to control EPA. It can be set to NULL, SWA, SWB, SWC, SWD or their lock modes LK-A, B, C, D. If you assign 3 position switch, such as SWB, SWC to control EPA, you can set 3 different end points. If you assign SWA,D, LK-A,D to control EPA, 2 different end points can be switched. If SW is set to NULL, EPA will keep the current values. The RATE below means the travel amount of the servo, which defaults to 100%. It can be set from 0, the minimum travel amount, to 120%, the maximum. You can adjust EPA of steering, throttle, channel 3, 4, 5, 6, 7 Take SWB, a 3 position switch as an example. Set SW to SWB. Push SWB and the position of SWB is shown in the right corner of the screen. UP-CENTRAL-DOWN. Push SWB UP first, set the largest travel amount, that is 120%. Please note, you can set different travel amount for the two sides of the channel in EPA. For example, for Steering, set the left side 120%, but the right side 110%. The value can be different for both sides. Push SWB Central, keep all channels the normal travel amount, that is 100% by default. Push SWB DOWN, set small travel amount. For steering, set both sides 80%. For throttle, set both sides 80% too. Setting is done. Push SWB UP-- the large travel amount Push SWB CENTRAL- all 100% travel amount Push SWB-DOWN-- the small travel amount. What’s the difference of EPA and Dual Rate? For, EPA, you can set different travel amount of a servo on either side from its neutral position. That means for one channel, you need to set two values. But for Dual rate, the travel amount of a servo is the same on either side. That means you only need to set one rate for each channel. For more details of RC6GS V3: https://www.radiolink.com/rc6gsv3 Purchase link of RC6GS V3: https://www.radiolink.com/rc6gsv3_whe... You can send mails to [email protected] if you have any questions during using our products.

How to Assign a Switch to Control Dual Rate on RC6GS V3/RC4GS V3?

The Game Changer! HobbyWing Doesn't Want You Knowing.

How to setup your Radiolink RC6GS, transmitter programing!

Introducing the features of the 6,600 yen 4CH transmitter "RC4GS"

Upgrade a Radiolink RC4GS V3 to RC6GS V3 in English. *MUST SEE* DIY, How to, Tutorial

THSPD Throttle Delay Function on RC6GS V3/RC6GS V2/RC6GS/RC4GS V3/RC4GS V2/RC4GS

R7FG Dual Antenna Receiver by RadioLink: ALL YOU NEED TO KNOW.!!

TX Low Power & Battery Power Supply Options of RC6GS V3/RC6GS V2/RC6GS/RC4GS V3/RC4GS V2/RC4GS

RadioLink Using ID SEED to control 2 different car independently

Best transmitter for RC - Radiolink RC6GS - EVERYTHING Explained!

A.B.S Function on RC6GS V3/RC4GS V3

5 quick tips on the RC6GS

Unbelievable Workers | Working with Talented Engineers #46 #fail #adamrose #smartworkers

The affordable Speed Run Radio with Launch Control - Radiolink RC6GS V3

Radiolink RC4GS-V3 - DRAG CAR SETUP - Launch Control + Throttle curve

Best Lipo batteries for your RC transmitter - Parallel mode & Best practices - Radiolink RC6GS V3

Radiolink RC6GS V3 Unboxing, Function Review, and Setting Cruise Control

Radiolink RC6GS v3(only) Launch button and Throttle Ramp quick guide

Radiolink Transmitter Tuning // Steering Limits // Throttle Curve

