COMPOUND REST ANGLES FOR THREADING, 0°, 29° , 30° OR 90°. Advantages & disadvantages of each angle.

This video attempts to answer the age old question about how the compound rest angle affects the cutting action during a single point threading operation on the lathe. 0, 29, 30 OR 90 DEGREES? Advantages and disadvantages of different compound rest angles. This video is part of a free online machine shop course accessible to everyone on my webpage THATLAZYMACHINIST.COM . No sign up, no subscription and no hassle, it's all free and always will be. As for all of my machine shop videos, this video is specifically produced for novice machinists. Thanks for understanding that I am a professional toolmaker and teacher but I am not a professional video producer (and it shows). I produce these videos for fun as a little retirement project that lets me give back a little of what was passed on to me by so many amazing trades people, most of whom, sadly, are no longer with us. Marc L'Ecuyer Thatlazymachinist.com Also of interest with this video: HAMMER HANDLE PART 4    • HAMMER HANDLE #4 INTRODUCTION TO LATHE WOR...   TAPER ATTACHEMENT, TAILSTOCK OFFSET TAPER CUTTING    • HAMMER HANDLE #4 INTRODUCTION TO LATHE WOR...   HAMMER HANDLE PART 3    • HAMMER HANDLE #3 INTRODUCTION TO LATHE WOR...   DIE THREADING, CONCAVE GROOVING & SHOULDER TURNING    • HAMMER HANDLE #3 INTRODUCTION TO LATHE WOR...   HAMMER HANDLE PART 2    • HAMMER HANDLE #2 INTRODUCTION TO LATHE WOR...   KNURLING, DRILLING & REAMING ON THE LATHE    • HAMMER HANDLE #2 INTRODUCTION TO LATHE WOR...   HAMMER HANDLE PART 1    • HAMMER HANDLE #1 INTRODUCTION TO LATHE WOR...   SURFACING, DRILLING & GROOVING ON THE LATHE    • HAMMER HANDLE #1 INTRODUCTION TO LATHE WOR...   POSITIONNING HAMMER'S HEAD    • THE HAMMER'S HEAD, TAPER & PARALLEL TURNIN...   FOUR JAW CHUCK CENTERING & TURNING SQUARE STOCK    • THE HAMMER'S HEAD, TAPER & PARALLEL TURNIN...   COMPOUND REST OFFSET TAPER TURNING    • THE HAMMER'S HEAD, TAPER & PARALLEL TURNIN...   POSITIONNING HAMMER'S PLUG & TIPS    • HAMMER'S PLUG & TIPS, PARALLEL TURNING, DR...   TURNING SMALL PARTS USING 5C COLLETS    • HAMMER'S PLUG & TIPS, PARALLEL TURNING, DR...   THREAD TAPPING ON THE LATHE    • HAMMER'S PLUG & TIPS, PARALLEL TURNING, DR...   CUTTING LIP ANGLES FOR TURNING    • CUTTING LIP ANGLES & TOOL HEIGHT FOR TURNI...   CENTERING PARTS IN 4 JAW CHUCKS    • CENTERING A FOUR JAW CHUCK (HOW TO) FOR DI...   THREADING ON THE LATHE    • THREADING ON THE LATHE, CHOOSING PLUNGE AN...   COMPOUND REST ANGLES FOR THREADING    • COMPOUND REST ANGLES FOR THREADING, 0°, 29...   SCREW JACK PROJECT PART 1    • SCREW JACK PART 1, lathe 101 Marc L'Ecuyer   PLANING SEQUENCE OF OPERATIONS & SIZING STOCK    • SCREW JACK PART 1, lathe 101 Marc L'Ecuyer   SCREW JACK PROJECT PART 2    • SCREW JACK PART 2, lathe 101 Marc L'Ecuyer   BALL TURNING TECHNIQUE FOR MACHINING THE PIVOT    • SCREW JACK PART 2, lathe 101 Marc L'Ecuyer   SCREW JACK PROJECT PART 3    • SCREW JACK PART 3, lathe 101 Marc L'Ecuyer   SINGLE POINT TOOL LEFT HAND THREADING ON THE LATHE    • SCREW JACK PART 3, lathe 101 Marc L'Ecuyer   SCREW JACK PROJECT PART 4    • SCREW JACK PART 4, lathe 101 Marc L'Ecuyer   CALCULATING & MEASURING THREADS BY THREE WIRE METHOD    • SCREW JACK PART 4, lathe 101 Marc L'Ecuyer   SCREW JACK PROJECT PART 5    • SCREW JACK PART 5, lathe 101 Marc L'Ecuyer   TAPPING LEFT HAND THREAD & TURNING RIGHT HAND THREAD    • SCREW JACK PART 5, lathe 101 Marc L'Ecuyer   SCREW JACK PROJECT PART 6    • SCREW JACK PART 6, lathe 101 Marc L'Ecuyer   SINGLE POINT INTERNAL THREADING ON THE LATHE    • SCREW JACK PART 6, lathe 101 Marc L'Ecuyer   HOW TO ACCURATELY TURN A SPHERE    • HOW TO MACHINE AN ACCURATE SPHERE BY HAND ...   HOW TO TURN A CROWN PULLEY    • MACHINING CROWNED PULLEYS OR ANY CONTOURED...   HOW TO MACHINE A SMALL CRANKSHAFT    • HOW TO MACHINE A SMALL STEAM ENGINE CRANKS...