Make Your Own Whiskey Tap Out Of Glass Building Blocks

In this video I'll show you how I took these vintage glass building blocks that were found in a barn and turn them into really cool whiskey tap/decanter. Two friends of mine sent me the same Crafty Panda Video where a guy takes a glass block and turns it into a whiskey tap. Well, One of those friends happened to have Vintage blocks in his barn for me to use. The video they sent me did not give specifics so I had to figure it out on my own. I show you how I did it with mistakes and all. Follow up Video with what I learned after make these:    • Make Your  Own Whiskey Tap Follow up video...   Follow up Part III:    • More Whiskey Tap Details as Requested   Live follow up I: https://www.youtube.com/live/m_q7aW9b... Live follow up II: https://www.youtube.com/live/9IeKNkkx... Materials and general dimensions below. (these have changed as I ran out of these blocks) General Dimensions: Frame: Four pieces cut to 7-5/16" X 3-3/16" with 45 degree bevel both sides Stand Legs: Two pieces cut to 4-1/2" X 3" with a 45 degree bevel on one side Stand: 8-3/4 X 5-1/2" (decorate how you like via edge profile) Spout Hole size: 16MM Stopper hole size 18MM ♦Tools/Material I used in the video 18 mm hole saw bit: https://amzn.to/3uQrMUv 16 mm hole saw bit: https://amzn.to/3V0qfpt 1/8” glass drill bits: https://amzn.to/3Bxmoth Drill press: https://amzn.to/3xJMjLy Drill press Fence: https://amzn.to/3ygwSf7 Strap Clamp: https://amzn.to/3OyXIVc Good hand saw: https://amzn.to/3bvymJS Impact driver I use: https://amzn.to/3xOQxBD Cordless Drill: https://amzn.to/3uV9v9d Best Tape Ever: https://amzn.to/3NwdY98 Sander: https://amzn.to/3bdWBMf Tight Bond II: https://amzn.to/3akXQsY Angle Finder: https://amzn.to/3yFfTST Glass blocks: https://amzn.to/3HygQAX Whiskey Tap Spigot: https://amzn.to/3S0jWlt Copper spigot: https://amzn.to/498awNJ Copper stoppers: https://amzn.to/3AVW0fv Plain Stoppers: https://amzn.to/3vacdaR Skull Stoppers: https://amzn.to/3zqzJ60 FDA sealent: https://amzn.to/3CJOLI2 Spray lacquer: https://amzn.to/3z5dNvS Funnels to fill it: https://amzn.to/3PyD0FP (I include one of these when someone buys one from me) ♦ Tools I recommend and use in my shop Awesome Shims: https://amzn.to/3NcHEHK Magnetic Wrist Screw Holder: https://amzn.to/3u07cAV The Jig Saw I Want When Mine Breaks: https://amzn.to/3HSbShW Good power Saw: https://amzn.to/3tYKRE1 Tight Bond Quick and Thick: https://amzn.to/3bX1gma I receive a small commission if you use any of these links for your purchase. It helps and Thank you! ♦ Channels I like to watch See My Home page for Featured Channels Mailing Address: PO Box 26596 Benbrook, TX 76126 Etsy link: https://www.etsy.com/listing/1270480811/ My Facebook:   / epeiuscustomwoodworking   My Instagram:   / epeius_garage   My TikTok: EpeiusGarage My Email: [email protected]