etrailer | Rhino-Rack T-Load Hitch Mounted Load Assist Review

Click for more info and reviews of this Rhino Rack Truck Bed Extender: https://www.etrailer.com/Truck-Bed-Ex... Check out some similar Truck Bed Extender options: https://www.etrailer.com/dept-pg-Truc... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-review-rh... Today, we're gonna be taking a look at a solution for some of those heavier kayaks and the solution to this is the Rhino-Rack T-Load Assist bar. So this is gonna be a hitch mounted accessory for your 2" hitch receiver. The nice thing about it is we fold it back like this. We can go ahead and take this up, get it kind of lined up with it. And typically we have the back end kind of slide out on us, but it does come with a little pad to protect your kayak from scratches, but also allowing it not to slide around. So now, if this is done, we'll take it. Clean it up. And I'm not really holding a whole lot of the weight. Which is nice. So now we can get it up here. Situate it. And then tie it down. So this is a lot easier, especially as the weight start to go up. This kayak's not that heavy, but some of those fishing kayaks they get kind of up there. So this is definitely gonna be the easiest way to load that thing up. What comes with the kit is these little load stops. So the angle right here, this is for your kayaks, but we can take this off, swap it around and then the flat side's gonna be for your lumber or ladders. You can tie down your kayak like you normally do. Cool thing about this is on the end, what I would do is to take this, throw it over the top. And use this as a strap. It's already there. It's nice and perfect length this, go in there, tie it down. And if we did have these load stops a little bit closer, the nice thing is we have this little piece underneath here to protect the for many scratches. And the way you adjust these load stops is squeeze them up a little bit, slide it on down. Done deal, if you really needed to do that. But then when I unload it, obviously the center of our kayak is a little bit wider, but just know you do have these adjustments here on both sides. Very easy, you don't need a tool or anything. You're good to go. This is basically just your Rhino-Rack, aero bar it's made of aluminum. It's got an aerodynamic shape to it, and it's about 49" long, which is pretty good for most loads. We wanna make sure that our whole entire setup's gonna work with your kayak. If you have a really, really heavy kayak just make sure it's not gonna be exceeding 165 pounds. So depending on what kind of car you have, what kind of rack you're working with, ladder rack or roof rack you can use the included tool to adjust this with the telescoping system. So once we loosen this up a couple turns, where we need it to. Lower it if we want to. Raise it up, if we really want to. tighten it back up. And once we find that perfect little spot for your kayak What you can do is come down to this little hole. We'll go ahead and tighten it up. And then with the hole, we'll just take a little drill bit. Drill this out right there and then do give us a clip to go through it to mark our spot. So we can adjust it real low to put it in our garage. And then whenever we want to use it, drill that hole, put this in and you know, you're all ready to rip. As you can see, it's perfectly level. Didn't take me a whole lot of time to get it level. And I think that's pretty neat. We can also do some more adjustments. We have a hole here, hole here or we can take the bolt out all together and that's gonna change how far it goes back. So in the highest setting, doesn't come back a whole lot. Not much at all. So that's how mark goes back there. And that's it upright. Let's take it off. Go to the second setting. Let's see how far it goes back. This is what we we're using earlier which this will change depending on what kind of roof you have and what kind of vehicle you have. So there's that one. And then let's take it out all together. Let's see. And that's kind of a lot. So it all just depends, just know you have adjustability there. And whenever we have it all loaded up we're gonna have this hole right here which we can take this through and it's gonna be locked into the place. Looking down further on our shank, again, this is where your 2" hitch receivers. We are gonna get an anti-rattle bolt on the end of it with a lock. So a lot of these accessories don't come with locks. This one does, which is awesome. And the anti-rattle bolt, what that does is just make sure it's nice and secure to your hitch. So you're not gonna hear any rattling at all. We're ready to catch some fish, pull the pin unstrap your yak, and then grab your yak. Go down like this, pull your yak. Put it down on the pad. Grab your yak and hit the water and catch some fish. I do like h