Morse Test Procedure | Indicated power, Brake power, Mechanical Efficiency | Power engineering

Subject - Power Engineering Chapter - Morse Test steps and Procedure for measuring Indicated power, Brake power, Friction Power and Mechanical Efficiency Timestamps 0:00 - Morse Test Procedure for measuring Indicated power on Multi Cylinder Petrol Engine 0:10 - Step 1: The engine is run at constant speed. 0:20 - Step 2: Brake power of engine is measured by dynamo meter when all four cylinders are working. 0:24 - What is Indicated power 1:03 - Step 3: First cylinder is cut out by short circuiting spark plug. 1:10 - Step 4: Speed falls because of non firing of first cylinder and speed restore by reducing the load on engine and torque is measured. 1:41 - Step 5: Repeat the above procedure for remaining cylinders and calculate I.P. of engine. 2:44 - How to determine Friction Power 2:57 - How to determine Mechanical Efficiency 3:14 - Assumption in Morse Test #Morse_Test_Procedure #Indicated_power #Brake_power #Friction_power This Video Topic is from Power Engineering Subject, you can also watch below mentioned videos related to Power Engineering Subject: Carnot Cycle -    • Carnot Cycle Working Animation | Thermodyn...   Otto Cycle -    • Otto Cycle Working Animation | Thermodynam...   Diesel Cycle -    • Diesel Cycle Working Animation | Thermodyn...   Dual Cycle -    • Dual Cycle Working Animation | Thermodynam...   Brayton Cycle or Joule Cycle -    • Brayton Cycle or Joule Cycle in Gas Turbin...   Knocking, Detonation and Pre-ignition -    • Knocking, Detonation and Pre-ignition [Eng...   Supercharger and Turbocharger -    • Supercharger and Turbocharger [Constructio...   Multi Point Fuel Injection (MPFI) System -    • Multi Point Fuel Injection (MPFI) System |...   Turning Moment Diagram (TMD) for Single Cylinder Four Stroke Engine -    • Turning Moment Diagram (TMD) for Single Cy...   Valve Timing Diagram of 2 & 4 Stroke Petrol [SI] & Diesel [CI] Engine -    • Valve Timing Diagram of 2 & 4 Stroke Petro...   Valve Timing Diagram of 2 Stroke Petrol Engine [SI engine] -    • Valve Timing Diagram of 2 Stroke Petrol En...   Valve Timing Diagram of 2 Stroke Diesel Engine [CI engine] -    • Valve Timing Diagram of 2 Stroke Diesel En...   Valve Timing Diagram of 4 Stroke Petrol Engine [SI engine] -    • Valve Timing Diagram of 4 Stroke Petrol En...   Valve Timing Diagram of 4 Stroke Diesel Engine [CI engine] -    • Valve Timing Diagram of 4 Stroke Diesel En...   Engine Terminology -    • Engine Terminology: Stroke, Bore, Swept vo...   Morse Test Procedure -    • Morse Test Procedure | Indicated power, Br...   Heat Balance Sheet of Engine -    • How to draw Heat Balance Sheet of Engine |...   Catalytic Converter (2 way and 3 way) -    • Catalytic Converter Working Principle: 2 w...   Intercooling, Regeneration, Reheating in Gas Turbine -    • Intercooling, Regeneration, Reheating in G...   Turbojet Engine and Turboprop Engine -    • Turbojet Engine and Turboprop Engine Worki...   Ramjet Engine -    • Ramjet Engine Working Animation | Ram Comp...   Entropy And Enthalpy -    • Entropy And Enthalpy: Crash Course Chemist...   Thermodynamic Processes: Isobaric, Isochoric, Isothermal and Adiabatic process -    • Carnot Cycle Working Animation | Thermodyn...   Faculty - Shubham Kola ( BE Mechanical Engineer ) Email ID - [email protected] From - Maharashtra ( India ) YouTube Channel ( Shubham Kola ) -    / @ifinfotech   Disclaimer - video is for educational purpose only. Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favour of fair use. The content in this video is collected from books, media, internet space etc. This is strictly for educational and information purposes and is not intended to be advice or recommendation of any kind whatsoever. The faculty is not a subject expert. The faculty is sharing his knowledge in the form of videos. The faculty giving small basics information on mechanical engineering topics. We endeavour to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the video or the information, related graphics contained in the video for any purpose. any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arise out of, or in connection with, the use of this video.