BOSCH GWS 11-125 CIE ANGLE GRINDER SERVICE BOSCH GWS 11-125 CIE कोना चक्की SERVICE

00:14 stops working when the cable moving 00:23 disassembly of Auxiliary Handle 00:31 disassembly the head from the body 01:00 disassembly of Protective Cover 01:16 disassembly of Round Nut M14 01:20 disassembly of Clamping-flange Ø22,3xØ42 MM 01:28 disassembly of Gear housing/Bearing Flange 01:35 disassembly of Catch Lever and spring 01:44 disassembly of Shim 0,3 MM 01:54 degrease 02:01 with the help of a vice and a 10 mm wrench i will unscrew the Hex Nut M7, SW10 02:14 disassembly ofArmature With Fan 220-240V 02:19 disassembly of Bevel Gear Z=11 02:22 disassembly of Push-button 02:37 disassembly of Housing Cover 02:53 disassembly of Cover 03:05 disassembly of Tapping ScrewDIN7981-ST3,9x13-C-Z/Fastening Clamp/ 03:18 HOW TO CHECK a cord of a POWER TOOL (SHORT lesson) 04:23 check of the cord 04:39 first wire fault detection 04:45 disassembly the wires of the Switch 05:44 disassembly of Compression Spring 05:51 disassembly of Air-deflector Ring 06:00 disassembly the wires of the Switch 06:17 disassembly the Switch 06:36 cleaning of the switch 06:53 clean the armature from the carbon with sandpaper 07:08 replace the Carbon-brush Set 07:29 second fault detection (detection of wire insulation wear) 07:50 wire repair 07:55 switch in place 08:01 switch wires assembly 08:10 assembly of Air-deflector Ring 08:17 assembly of Compression Spring 08:21 lubricate the spring (10 TIMES ON OFF ) 08:32 connect the wires of the cord with the switch 08:37 connecting wires to the switch 08:45 assembly the wires of the switch 09:08 assembly of Tapping ScrewDIN7981-ST3,9x13-C-Z/Fastening Clamp 09:19 assembly of Housing Cover with Motor Housing 09:29 assembly of Cover 09:34 assembly of Tapping Screw DIN7981-ST3,9x19-F-Z 09:43 lubricate the Push-button 09:55 assembly of Push-button 10:15 assembly of Bevel Gear Z=11with Armature With Fan 220-240V 10:33 screw the hex Hex Nut M7, SW10 with a wrench key 10 mm 11:08 lubricate the gears 11:52 assembly of Catch Lever /Spring 12:13 assembly of Grinding Spindle M14, SW17/Crown Gear Z=38//Gear Housing 12:45 assembly of Armature With Fan220-240V with Housing Cover and Motor Housing 13:12 assembly of Grommet Ø7,3-Ø8,6x67 MM 13:16 assembly of Cover/Tapping Screw DIN7981-ST3,9x19-F-Z 13:56 test 14:06 check of Power Supply Cord EU 4,15m 2 x 1,0mm H07 RN-F 14:23 third fault detection 14:35 remove the damage part (first attempt) 14:55 check for signal 15:23 remove the damage part (second attempt) 15:48 check for signal 16:16 replace the old part with new 21:00 check for signal (coonect the two wires to the switch) 21:14 final test